Sponsored Content
Full Discussion: Help with VLANs
Top Forums UNIX for Dummies Questions & Answers Help with VLANs Post 302510977 by rama krishna on Tuesday 5th of April 2011 11:45:35 AM
Old 04-05-2011
Help with VLANs

Hi Gurus,

Can anyone explain me what is a Vlan and a Native vlan. How to check the native Vlan on my server having a solaris10 OS.

Thanks in advance.Smilie
 

5 More Discussions You Might Find Interesting

1. IP Networking

vlans

Hi All, I'm trying to configure a vlan interface, to do this I'm using the following command "vconfig add eth0 20". I have my interface up and running, but when I test it using "ping -I eth0.20 192.168.1.1" and in other console use "tcpdump -i eth0.20" I can not see any tagged frame. ... (0 Replies)
Discussion started by: lagigliaivan
0 Replies

2. AIX

AIX / Etherchannel / VLANs

I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks. (5 Replies)
Discussion started by: jwholey
5 Replies

3. Solaris

Oracle VMs and VLANs

I've been given an IP address to assign to an ldom that is in a different subnet than the host, and I am looking for assistance in getting it online. I believe I need "VLAN tagging" as found in this link, but I do not understand all of the terminology. My host machine is on subnet 10.25.112.x,... (1 Reply)
Discussion started by: bstring
1 Replies

4. IP Networking

VLANs and their domains

Hey everyone. I work in a data center, and I'm working on getting my CCNA. Now when I read articles on the idea of VLAN's it makes sense. Especially if you have multiple switches daisy chained in multiple locations. My two main questions though are that most of these examples use PC's as examples... (2 Replies)
Discussion started by: Lost in Cyberia
2 Replies

5. Proxy Server

Linux Networking - VLANs & Multiple IP's

In a "typical" data centre environment (telco, financial services etc), would a Linux OS typically have one IP address connected to one VLAN or would it have many IPs and/or VLANs. I say "Linux OS" as I'm referring to an instance of the OS not necessarily a Host or server. Think Linux OS = VM in a... (9 Replies)
Discussion started by: PCB
9 Replies
VLAN(4) 						   BSD Kernel Interfaces Manual 						   VLAN(4)

NAME
vlan -- IEEE 802.1Q VLAN network interface SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file: device vlan Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5): if_vlan_load="YES" DESCRIPTION
The vlan driver demultiplexes frames tagged according to the IEEE 802.1Q standard into logical vlan network interfaces, which allows rout- ing/bridging between multiple VLANs through a single switch trunk port. Each vlan interface is created at runtime using interface cloning. This is most easily done with the ifconfig(8) create command or using the cloned_interfaces variable in rc.conf(5). To function, a vlan interface must be assigned a parent interface and numeric VLAN tag using ifconfig(8). A single parent can be assigned to multiple vlan interfaces provided they have different tags. The parent interface is likely to be an Ethernet card connected to a properly configured switch port. The VLAN tag should match one of those set up in the switched network. Initially vlan assumes the same minimum length for tagged and untagged frames. This mode is selected by the sysctl(8) variable net.link.vlan.soft_pad set to 0 (default). However, there are network devices that fail to adjust frame length, should it fall below the allowed minimum due to untagging. Such devices should be able to interoperate with vlan after changing the value of net.link.vlan.soft_pad to 1. In the latter mode, vlan will pad short frames before tagging them so that their length stays not less than the minimum value after untagging by the non-compliant devices. HARDWARE
The vlan driver supports efficient operation over parent interfaces that can provide help in processing VLANs. Such interfaces are automati- cally recognized by their capabilities. Depending on the level of sophistication found in a physical interface, it may do full VLAN process- ing or just be able to receive and transmit long frames (up to 1522 bytes including an Ethernet header and FCS). The capabilities may be user-controlled by the respective parameters to ifconfig(8), vlanhwtag and vlanmtu. However, a physical interface is not obliged to react to them: It may have either capability enabled permanently without a way to turn it off. The whole issue is very specific to a particular device and its driver. By now, the list of physical interfaces able of full VLAN processing in the hardware is limited to the following devices: ae(4), age(4), alc(4), ale(4), bce(4), bge(4), cxgb(4), em(4), ixgb(4), jme(4), msk(4), nge(4), re(4), sge(4), stge(4), ti(4), txp(4), and vge(4). The rest of the Ethernet interfaces can run VLANs using software emulation in the vlan driver. However, some of them lack the capability of transmitting and receiving long frames. Assigning such an interface as the parent to vlan will result in a reduced MTU on the corresponding vlan interfaces. In the modern Internet, this is likely to cause tcp(4) connectivity problems due to massive, inadequate icmp(4) filtering that breaks the Path MTU Discovery mechanism. The following interfaces support long frames for vlan natively: bfe(4), cas(4), dc(4), fwe(4), fxp(4), gem(4), hme(4), le(4), nfe(4), nve(4), rl(4), sf(4), sis(4), sk(4), ste(4), tl(4), tx(4), vr(4), and xl(4). The vlan driver automatically recognizes devices that natively support long frames for vlan use and calculates the appropriate frame MTU based on the capabilities of the parent interface. Some other interfaces not listed above may handle long frames, but they do not advertise this ability of theirs. The MTU setting on vlan can be corrected manually if used in conjunction with such a parent interface. SEE ALSO
ifconfig(8), sysctl(8) BUGS
No 802.1Q features except VLAN tagging are implemented. BSD
April 14, 2010 BSD
All times are GMT -4. The time now is 06:06 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy