Sponsored Content
Operating Systems Solaris Re-sync Taking Extremely Long. Post 302500137 by ravzter on Sunday 27th of February 2011 10:58:56 AM
Old 02-27-2011
Making plans to replace them tonight.
I also looked at /etc/system earlier and that buffersize=2048 parameter is set for both primary and standby.

Thanks for the link! I read it to see if there's a command that would show the buffer size being used during the re-attach.
 

10 More Discussions You Might Find Interesting

1. Programming

fwrite takes extremely long time

After my previous thread, I think I found out what causes the long delays. I run this program on several Linux computers, and the sometimes (after the file with the arrays becomes big) the fwrite takes between 100 ms to 900 ms. This is very bad for me, as I want a timer to halt each 30 ms.... ... (5 Replies)
Discussion started by: inna
5 Replies

2. Red Hat

login process taking a long time

I'm having a bit of a login performance issue.. wondering if anyone has any ideas where I might look. Here's the scenario... Linux Red Hat ES 4 update 5 regardless of where I login from (ssh or on the text console) after providing the password the system seems to pause for between 30... (4 Replies)
Discussion started by: retlaw
4 Replies

3. Shell Programming and Scripting

For Loop Taking Too Long

I'm new from UNIX scripting. Please help. I have about 10,000 files from the $ROOTDIR/scp/inbox/string1 directory to compare with the 50 files from /$ROOTDIR/output/tma/pnt/bad/string1/ directory and it takes about 2 hours plus to complete the for loop. Is there a better way to re-write the... (5 Replies)
Discussion started by: hanie123
5 Replies

4. UNIX for Advanced & Expert Users

Comparison and For Loop Taking Too Long

I'd like to 1. Check and compare the 10,000 pnt files contains single record from the /$ROOTDIR/scp/inbox/string1 directory against 39 bad pnt files from the /$ROOTDIR/output/tma/pnt/bad/string1 directory based on the fam_id column value start at position 38 to 47 from the record below. Here is... (1 Reply)
Discussion started by: hanie123
1 Replies

5. UNIX for Dummies Questions & Answers

gref -f taking long time for big file

grep -f taking long time to compare for big files, any alternate for fast check I am using grep -f file1 file2 to check - to ckeck dups/common rows prsents. But my files contains file1 contains 5gb and file 2 contains 50 mb and its taking such a long time to compare the files. Do we have any... (10 Replies)
Discussion started by: gkskumar
10 Replies

6. UNIX for Dummies Questions & Answers

Job is taking long time

Hi , We have 20 jobs are scheduled. In that one of our job is taking long time ,it's not completing. If we are not terminating it's running infinity time actually the job completion time is 5 minutes. The job is deleting some records from the table and two insert statements and one select... (7 Replies)
Discussion started by: ajaykumarkona
7 Replies

7. UNIX for Dummies Questions & Answers

ls is taking long time to list

Hi, All the data are kept on Netapp using NFS. some directories are so fast when doing ls but few of them are slow. After doing few times, it becomes fast. Then again after few minutes, it becomes slow again. Can you advise what's going on? This one directory I am very interested is giving... (3 Replies)
Discussion started by: samnyc
3 Replies

8. Shell Programming and Scripting

While loop problem taking too long

while read myhosts do while read discovered do echo "$discovered" done < $LOGFILE | grep -Pi "|" | egrep... (7 Replies)
Discussion started by: SkySmart
7 Replies

9. Shell Programming and Scripting

Rm -rf is taking very long, will it timeout?

I have so many (hundreds of thousands) files and directories within this one specific directory that my "rm -rf" command to delete them has been taking forever. I did this via the SSH, my question is: if my SSH connection times out before rm -rf finishes, will it continue to delete all of those... (5 Replies)
Discussion started by: phpchick
5 Replies

10. AIX

HACMP - two nodes - take too long to sync

HI Admin, I have running 2 node HACMP cluster- AIX 6.1. I just set it up. It does sync completely without any errors. But it take too long to sync. More than 30 mins... any reasons? Where can I start looking into ? Same network, same Subnet (1 Reply)
Discussion started by: snchaudhari2
1 Replies
sb2-session(1)						       sb2-session man page						    sb2-session(1)

NAME
sb2-session - manage scratchbox2 sessions SYNOPSIS
sb2-session [COMMAND [PARAMS]] DESCRIPTION
sb2-session is used to create attachable scratchbox2 sessions. You can save session even when you haven't done '-S session' during sb2 startup. Note that you can give parameters to attach command which are passed verbatim to sb2. If there is only one session to attach, it is selected automatically. If no command is given, help text is printed. COMMANDS
help shows help text save saves current session list lists detached sb2 sessions delete SESSION deletes given session attach [SESSION [PARAMS]] attaches to a given session setenv VARIABLE VALUE store a value for an environment variable showenv show stored environment variables EXAMPLES
Basic usage is: [SB2 .. ] $ sb2-session save # save session [SB2 .. ] $ ^D # exit Later we can then attach to this session: % sb2-session attach If there are more than one saved session, then: % sb2-session list session.XXXX TARGET_ARM My Comment session.YYYY TARGET_ARM My Comment 2 session.ZZZZ TARGET_MIPS % sb2-session attach session.YYYY Here we pass '-eR' to sb2 and we only have one saved session: % sb2-session attach -- -eR '--' marks end of parameter list for sb2-session. setenv VARIABLE VALUE can be used to add environment variables, that will become active when a saved session is later taken into use (either by sb2-session attach or by sb2 -J). setenv VARIABLE VALUE does not change environment of sessions that are already active. showenv lists environment variable settings which have been stored with this tool. It does not show environment variables from other sources. SEE ALSO
sb2(1) AUTHOR
Mika Westerberg 2.2 21 December 2010 sb2-session(1)
All times are GMT -4. The time now is 11:47 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy