02-24-2011
smurphy,
Thanks a bunch for the advice. I switched out of the restricted shell to get root access and grepped for http. Sure enough, it wasn't running. Executing "/usr/ios/lpm/sbin/httpdmgr start" gave me an error stating that lwistart.sh was not running. I located that at /usr/ios/lpm/gui/httpd/bin/ and executed it. That's now running, and when I run httpdmgr start it now says "Error: lwistart.sh is already running. Done" So I'm not sure what this thing wants. It's not happy whether or not lwistart.sh is running. Seems to be sending me in circles. So I ended up opening a PMR with IBM and I'll post the solution when we find one.
Thanks!
---------- Post updated at 11:24 AM ---------- Previous update was at 11:20 AM ----------
HA! Guess I spoke too soon. I just checked the IVM web interface again after posting my reply and now it's available. So it apparently needs some time after executing lwistart.sh before it becomes available. Seemed to take about 10 minutes.
Thanks again, smurphy. Your advice worked. I just needed a little patience.
10 More Discussions You Might Find Interesting
1. AIX
I have a running VIO server that was managed via IVM. We made the (apparent) mistake of trying to connect a HMC server to it. Other than making a connection, no work has been done via HMC. We've since decided we don't want to use HMC and it's been powered off for a couple of weeks. However,... (1 Reply)
Discussion started by: cjs226
1 Replies
2. AIX
I have a bladecenter and js22, how to login IVM's command line such as HMC command line? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
3. AIX
Hi guys,
I am kind of new to this PowerVM thing.
I have created a virtual disk and partition.
With the IVM, when I try to open terminal wndow, a virtual terminal appeared and ask for password.
it says there:
In order to acess the terminal, you must first authenticate with IVM
Hostname... (2 Replies)
Discussion started by: wingcross
2 Replies
4. UNIX for Advanced & Expert Users
Solaris 10 Server refuse to connect :wall:
fork: Resource temporarily unavailable , server unexpectedly unavailable network connection , refuse error, disconnect message, fatal error type2, (protocol error type2)
Issue has been resolved after taken few steps :b:
First of all need to check... (1 Reply)
Discussion started by: taherahmed
1 Replies
5. AIX
Can somebody help me on IVM? I have installed vio 2.2 on a js21 server.
It has 2 physical ether ports, what I want to do is create ether channel say
en15 and en16 are physical and en17 is ether channel. I have created 2 clients on this server, now the question is can I map this en17 to both... (1 Reply)
Discussion started by: vjm
1 Replies
6. AIX
Hello,
Lets say for simplicity that I do not use any vlan config inside my server - one lpar group use hea physical port1, another group hea physical port2. Physical port1 configured as vlan1 on external switch, physical port2 as vlan2.
What is the common practice - should I isolate my vios... (0 Replies)
Discussion started by: vilius
0 Replies
7. AIX
Hi,
When I try to login on my vios ivm website http://vios through the browser -- all three of them -- firefox , chrome , Internet Explorer , i get this error
http://vioserver/j_security_check
I have java installed on the machine from where i am trying to open up the IVM/VIOS webpage.
I... (2 Replies)
Discussion started by: filosophizer
2 Replies
8. AIX
I am facing problems in moving CD-ROM from one lpar to another.
CDROM can be seen on the POWERVM (IVM) server , but through the web-access if I move it ( assign it ) to LPAR it will be assigned. I run cfgmgr , and the cdrom does not show up in the LPAR. I firmly believe this is the reason why I... (2 Replies)
Discussion started by: filosophizer
2 Replies
9. AIX
Hi All,
I have a p520 box running 3 LPARs, 1 x VIOS, 1 x AIX 6.1 and 1 x AIX 7.1 and no HMC, all configuration is performed via VIOS/IVM
Until recently the box did not have the AIX7.1 LPAR and everything was fine with the box.
We needed to use AIX 7.1 for a new project, so I created a... (11 Replies)
Discussion started by: KevB
11 Replies
10. AIX
Hello,
After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 )
i get this message
"I/O hosting requires a hosting partition - boot not permitted".
HMC was connected to the machine
then HMC was removed through ASMI
Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT CENTOS
ccw_device_start_key
CCW_DEVICE_START_KEY(9) The ccw bus CCW_DEVICE_START_KEY(9)
NAME
ccw_device_start_key - start a s390 channel program with key
SYNOPSIS
int ccw_device_start_key(struct ccw_device * cdev, struct ccw1 * cpa, unsigned long intparm, __u8 lpm, __u8 key, unsigned long flags);
ARGUMENTS
cdev
target ccw device
cpa
logical start address of channel program
intparm
user specific interruption parameter; will be presented back to cdev's interrupt handler. Allows a device driver to associate the
interrupt with a particular I/O request.
lpm
defines the channel path to be used for a specific I/O request. A value of 0 will make cio use the opm.
key
storage key to be used for the I/O
flags
additional flags; defines the action to be performed for I/O processing.
DESCRIPTION
Start a S/390 channel program. When the interrupt arrives, the IRQ handler is called, either immediately, delayed (dev-end missing, or
sense required) or never (no IRQ handler registered).
RETURNS
0, if the operation was successful; -EBUSY, if the device is busy, or status pending; -EACCES, if no path specified in lpm is operational;
-ENODEV, if the device is not operational.
CONTEXT
Interrupts disabled, ccw device lock held
AUTHOR
Cornelia Huck <cornelia.huck@de.ibm.com>
Author.
COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 CCW_DEVICE_START_KEY(9)