01-10-2011
I'll check on it, thanks.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Sorry if this is not the right folder...
I come across these terms..
-Disk Array
-Clustering
What are they? When and how will we use them?
Please teach me.
Thanks (1 Reply)
Discussion started by: champion
1 Replies
2. Solaris
Hello friends, i have a problem with the pinout of T3 Array Disk cuz i don't know to build this serial cable :( please anybody help me! (1 Reply)
Discussion started by: nikoxve
1 Replies
3. Solaris
Do you know how do I make my solaris 8 detect the storEDGE A5000?.
I have problem making it recognise, without that I cannot install VxVM.
Any ideas? (7 Replies)
Discussion started by: calsum
7 Replies
4. Solaris
I am new to the unix world. I have SunBlade 100 and A1000 Disk storage array with 12 Hard drives. I used SCSI card and SCSI cables to connect. When I do the format command,I can see disk storage as one disk instead of 12 disks as below. Could anybody can explain why?
What should I do in order... (1 Reply)
Discussion started by: Dulasi
1 Replies
5. UNIX for Advanced & Expert Users
I have a 3510 disk array attached to a T2000 server.
The dmesg command shows disk error as follows and is generated a couple of times during the day
Aug 18 03:35:51 myserver SUNWscsdMonitor: <rctrl6042> Standard General Event, CHL:2 ID:22 Drive NOTICE: Drive Recovered Error - 5F8E1F... (1 Reply)
Discussion started by: Tirmazi
1 Replies
6. Solaris
I would want to ask on what software do i need to configure disk array for StorEdge A1000. (Sun Enterprise 450 - currently installed with SUN Solaris 9.)
Is it using RAID Manager 6.22? And is it compatible with SUN Solaris 9 or 10?
Thanks in advance for reading or replying my post. (2 Replies)
Discussion started by: beginningDBA
2 Replies
7. UNIX for Advanced & Expert Users
HI:
I have a DUAL redundant system running in HP-UX 10.20 ( 2 servers)
Both servers share an external SCSI disk array. Both server runs a Data base wich uses the disk array to write the data, and that is the way they share the information.
The way that the servers see the disk array, is like... (1 Reply)
Discussion started by: pmoren
1 Replies
8. UNIX for Dummies Questions & Answers
Hi there,
I've setup a raid0 array of 3 identical disks using :
mdadm --create --verbose /dev/md0 --level=stripe --raid-devices=3 /dev/sdb1 /dev/sdc1 /dev/sdd1I'm using dstat to monitor the disk activity :
dstat --epoch -D sdb,sdc,sdd --disk-util 30The results show that the stress is not... (8 Replies)
Discussion started by: chebarbudo
8 Replies
9. Filesystems, Disks and Memory
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (1 Reply)
Discussion started by: terrya
1 Replies
10. AIX
Hello,
On 4/20/2018, we performed a disk replacement on our IBM 8202 P7 server. After the disk was rebuilt, the SAS Disk Array sissas0 showed a status of degraded. However, the pdisks in the array all show a status of active.
We did see a message in errpt. DISK ARRAY PROTECTION SUSPENDED.
... (3 Replies)
Discussion started by: terrya
3 Replies
LEARN ABOUT X11R4
filecap
FILECAP:(8) System Administration Utilities FILECAP:(8)
NAME
filecap - a program to see capabilities
SYNOPSIS
filecap [ -a | -d | /dir | /dir/file [cap1 cap2 ...] ]
DESCRIPTION
filecap is a program that prints out a report of programs with file based capabilities. If a file is not in the report or there is no
report at all, no capabilities were found. For expedience, the default is to check only the directories in the PATH environmental variable.
If the -a command line option is given, then all directories will be checked. If a directory is passed, it will recursively check that
directory. If a path to a file is given, it will only check that file. If the path to the file includes capabilities, then they are written
to the file.
OPTIONS
-a This tells the program to show all capabilities starting from the / directory. Normally the PATH environmental variable is used to
show you capabilities on files you are likely to execute.
-d This dumps all capabilities for reference.
EXAMPLES
To check file capabilities in $PATH:
filecap
To check file capabilities of whole system:
filecap -a
To check file capabilities recursively in a directory:
filecap /usr
To check file capabilities of a specific program:
filecap /bin/passwd
To list all possible capabilities:
filecap -d
To set a file capability on a specific program:
filecap /bin/ping net_raw net_admin
SEE ALSO
pscap(8), netcap(8), capabilities(7).
AUTHOR
Steve Grubb
Red Hat March 2009 FILECAP:(8)