Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: add SSA pdisk to array to become hdisk
Operating Systems AIX add SSA pdisk to array to become hdisk Post 302483616 by kwliew999 on Monday 27th of December 2010 11:03:17 PM
Old 12-28-2010
add SSA pdisk to array to become hdisk
May I know how can I add a new SSA pdisk into array and become usable hdisk? I have inserted a 36GB SSA disk into enclosure and done the "cfgmgr" and I can see it already been regconized as pdisk47.
I would like to make it a system disk in order for me to add to my volume group. Please let me know how to do it?
Thanks.
 

10 More Discussions You Might Find Interesting

1. AIX

RS6000 SSA Raid question

Hi Can I add disks on the fly to extend the capacity of an existing RAID 5 volume? It's created on a 4P Advanced SSA Raid Adapter. I need to extend a volume group, so I figured it would be easiest to extend the "physical disk" which is a RAID5 volume. Thanks. (1 Reply)
Discussion started by: osee
1 Replies

2. AIX

ssa performances

Helo: We updated form AIX 4.3.3 to AIX 5.1-7 and after this we spent more than double time in read from external disks. Aparently the ssa cards microcode is at last level and all the ptf and apars are instaled. Out backups expent more than double time, but curiously in read only, if we write in... (0 Replies)
Discussion started by: Javier Gutierre
0 Replies

3. AIX

updating ssa

I am in the process of updating ssa adapters, drives and enclosures and wanted to know if there are any caveats that anyone would like to share. The documentation is not very clear on the ordering of the updates. Any tips would be appreciated. (1 Reply)
Discussion started by: chosie
1 Replies

4. AIX

Problem with a SSA drive

I've a problem with an IBM StorageWorks - Seagate SSA drive, model ST373453LC (IBM P/N 24P3733, Type S53D073, 72,8 GB 15K - USCSI 4 - 320 SSA). I bought this disk used but working; it came from an unknown IBM SSA storage array. I've removed the SCA - SSA adapter (IBM 18P3051 - 001 - R0) and i tried... (0 Replies)
Discussion started by: Linolinux
0 Replies

5. AIX

Location code for pdisk

Hi , I was migrating an AIX 5.2 system to AIX 5.3. I have hdisk8 and hdisk2 mirrored under rootvg. Below is the lscfg -vp output for the disks. hdisk8 U0.1-P1-I1/Q1-W40AABDDCC800D SSA Logical Disk Drive hdisk2 U0.1-P1-I1/Q1-W90D6151DEE00D SSA Logical Disk Drive I... (1 Reply)
Discussion started by: Muktesh
1 Replies

6. AIX

migrate from ssa to san

Hi, Do you have procedures to migrate ssa disks to san disk? I don't have testing environment and I want my file system be migrated one at a time. I want it to be fast, I have only 15-20 hours to do it on every sunday 1PM till monday 7am. My largest file system is about 150G. The AIX is... (0 Replies)
Discussion started by: itik
0 Replies

7. AIX

mirroring ssa to san

Hi guys, I'd like to share my migration/mirroring of ssa to san. No downtime for users, probably I/O performance. here's the step: 1 After the lun had been carved on the SAN and the connections had been done on AIX fiber card 2 “lspv” and look for the new SAN hdisk? on the bottom, say... (1 Reply)
Discussion started by: itik
1 Replies

8. AIX

Procedure for removing SSA array

Hi All, What's the proper procedure for removing SSA arrays? Is the procedure like these? - rmdev ssa disk - physical turn off the ssa - cfgmgr There's no more filesystem or logical volume on it. It's just pdisk and hdisk. Thanks in advance, itik (3 Replies)
Discussion started by: itik
3 Replies

9. AIX

VPATHS and HDisk/not able to add to NR-VG

When I list the PV's using lspv i see both vpath and hdisk names being listed. I got the info that each vpath is configured for 4 hdisks. Problem is I am not able to add either the hard disks in vpath to the existing non-rootvg. ? need to know the basics of vpath .. (4 Replies)
Discussion started by: nivaspIND
4 Replies

10. AIX

Replaced pdisk not showing up in SAS Disk Array Configuration

OSLevel: 5300-10-02-0943 System Model: IBM,8203-E4A Power 6 == Hi! I replaced a failed pdisk in the raid enclosure as follows, - rmdev -l 'pdisk18' '-d' - Replaced it. - cfgmgr (detected) - I can see the new drive, with the correct serial # lscfg -v -l pdisk18 pdisk18... (2 Replies)
Discussion started by: estrar
2 Replies

LEARN ABOUT HPUX

pvremove

pvremove(1M)															      pvremove(1M)

NAME

       pvremove - remove LVM data structure from a physical volume

SYNOPSIS

DESCRIPTION

       The  command  clears  the LVM data structure on a disk, so that it is no longer an LVM physical volume.	The device may then be used by the
       file system or by other volume managers.

       The operation is denied if pv_path is assigned to a volume group.  The command only clears the LVM data structure on a  disk  if  the  disk
       does not belong to a volume group.  This avoids accidentally removing a valid physical volume under a volume group.  If the physical volume
       to be removed belongs to a volume group, use the command to first remove the volume group associated with the physical volume.

   Arguments
       recognizes the following arguments:

	      pv_path	The character (raw) device path name of a physical volume.

EXTERNAL INFLUENCES

   Environment Variables
       determines the language in which messages are displayed.

       If is not specified or is null, it defaults to "C" (see lang(5)).

       If any internationalization variable contains an invalid setting, all internationalization variables default to "C" (see environ(5)).

EXAMPLES

       Remove LVM data structure on the physical volume

SEE ALSO

       lvremove(1M), vgremove(1M), intro(7), lvm(7).

																      pvremove(1M)
All times are GMT -4. The time now is 05:54 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy