12-19-2010
Dear Duke,
Thanks for the reply,
Yes I am going to put RAID 1 , if i want to use with different controllers , how can i do it. And also where can i find the controllers information in solaris. So that I can use the available controllers.
Thanks and Regards
Jr
9 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
My cutomer wants to set up a OS/apps server with two 72GB drives
configured with RAID 1+0. The way I understand RAID 1+0 is
that if there was a drive failure the whole OS/apps is lost because you
actually need at least 4 drives to set up a RAID 1+0 by splitting
them up into two arrays. Am I... (4 Replies)
Discussion started by: bdsffl
4 Replies
2. Solaris
hai everybody n good morning........here r some queries.......
1. what is the interlace value in RAID 0 (striping.......)
2. How many no of metadevices are required for mirroring and why......... (1 Reply)
Discussion started by: sudhansu
1 Replies
3. Solaris
hi all...sudhansu here............ i need some help..........
what is RAID 0+1 and RAID 1+0.............what is the difference between them................
suppose i have 80 gb disk space,then which RAID level i follow n why......... i need redundancy n maximum storage..........please help (3 Replies)
Discussion started by: sudhansu
3 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Solaris
Hello All,
I have read enough of texts on Raid 01 and Raid 10 on solaris :wall: . But no-where found a way to create them using SVM. Some one pls tell me how to do or Post some link if that helps.
TIA
Curious
solarister (1 Reply)
Discussion started by: Solarister
1 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. UNIX for Dummies Questions & Answers
Hi Gurus,
Can any one explain me the difference between hardware RAID and s/w RAID.
Thanks in Advance. (1 Reply)
Discussion started by: rama krishna
1 Replies
8. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
9. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT NETBSD
hptide
HPTIDE(4) BSD Kernel Interfaces Manual HPTIDE(4)
NAME
hptide -- Triones/Highpoint IDE disk controllers driver
SYNOPSIS
hptide* at pci? dev ? function ? flags 0x0000
DESCRIPTION
The hptide driver supports the Triones/Highpoint HPT366, HPT370, HPT370A, HPT372 and HPT374 IDE controllers, and provides the interface with
the hardware for the ata(4) driver.
The 0x0002 flag forces the hptide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
BUGS
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
October 8, 2003 BSD