12-10-2010
thanks DukeNuke2 for you reply
what i am asking is ==> a physical interface
10 More Discussions You Might Find Interesting
1. IP Networking
Hi,
I bound a virtual IP to a network card on my E450 server and I am getting this error when I reboot the server, saying, " retrying host, RPC time out. I had to break this sequence and allow other services to load. Of course they didn't load properly. Please how can I sort this out? I do need... (8 Replies)
Discussion started by: Ronny
8 Replies
2. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
5. Solaris
Hi,
I have installed oracle 10g release 2 on solaris 10 Zone. I want to configure ASM in local Zone using virtual disks in place of real disks.
I have configured ASM using virtual disks in place real disk in Solaris 10 Global zone. How i can do in local Zone
Kindly guid me with proper... (1 Reply)
Discussion started by: malikshahid85
1 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. Solaris
Trying to set or modify the randomly set hostID of a Solaris 10 virtual/guest machine that I installed on a Windows-XP host machine (using Virtual Box 4.1.12).
I was able to set/modify the hostname of the Solaris 10 virtual/guest machine during installation as well as via the Virtual Box... (4 Replies)
Discussion started by: Matt_VB
4 Replies
8. Red Hat
am try to create another network card as virtual eth0:1
but when i restart the server it want be appear i have to create it again what is the solution for this . (6 Replies)
Discussion started by: leganti
6 Replies
9. Solaris
have been trying to create a 2 GB ramdisk (virtual) to run on my T-2000 simulator (Legion) which has sun4v architecture. I have a SPARC workstation which runs on sun4u architecture with Solaris 10.
I have created a ramdisk image using dd command, newfs, then used ufsrestore to restore the... (3 Replies)
Discussion started by: Zam_1234
3 Replies
10. UNIX for Beginners Questions & Answers
I'm trying to migrate a Solaris 10 flar archive from a Sun M3000 to a T4-1. When I first created the zone I followed the Oracle instructions here: Transitioning an Oracle Solaris 10 Instance to an Oracle Solaris 11 System - Transitioning From Oracle Solaris 10 to Oracle Solaris 11 That worked... (6 Replies)
Discussion started by: Michele31416
6 Replies
lvmpvg(4) Kernel Interfaces Manual lvmpvg(4)
NAME
lvmpvg - LVM physical volume group information file
SYNOPSIS
DESCRIPTION
is an ASCII file that stores the volume-group information for all of the physical volume groups in the system. The information is stored
in a hierarchical format.
First, it starts with a volume group under which multiple physical volume groups can exist. Under each physical volume group, a list of
physical volumes can be specified. There must be at least one physical volume group in each volume group that appears in this file. The
physical-volume-group name must be unique within the corresponding volume group, although it is permissible to use a common physical volume
group name across different volume groups. There can be as many volume groups in this file as there are in the system.
Instead of using the and commands, the administrator can edit this file to create and extend physical volume groups. However, care must be
taken to ensure that all physical volumes to be included in the file have already been defined in their respective volume groups by previ-
ous use of or
The file format has the following structure. and are keywords that introduce the names of the volume group and physical volume group,
respectively.
pv_path
...
pv_path
...
pv_path
...
The variables are defined as follows:
pv_path The block device path name of a physical volume within the volume group.
pvg_name The name of the physical volume group. It must be unique within the volume group.
vg_name The path name of the volume group.
EXAMPLES
The following example shows an file containing two volume groups: the first containing two physical volume groups, each with two physical
volumes defined in it; the second containing three physical volume groups, each with one physical volume defined in it.
SEE ALSO
vgcreate(1M), vgextend(1M), vgreduce(1M), vgremove(1M), intro(7), lvm(7).
lvmpvg(4)