if your cmos time is wrong then you logon in single user mode.
Set the correct time and reboot your system.
open license manager and be sure the all settings are ok.
if your problem continues then re-try restore from tape and repeat up directions..
if your problem continues then check the your backup for corruption
Hi i am using HPUX
and i want to know wht is the command to see the listing from the tape device..
i have taken the backup
using cpio -ocvB>/dev/rmt/0m
while seeing the listing using
cpio -itvB</dev/rmt/0m
it is not showing the listing giving message -c option sd be there if i put -c... (1 Reply)
SCO/Caldera Unixware 711
Hi Friends,
I have a cpio file which was created using relative pathnames.
the relative pathname is users/data/*
I want to restore these files to a different directory with cpio.
An example restore directory is /home/suresh
Is this possible ?
Can someone... (4 Replies)
Hi All,
I have a tape backup(DDS2) with cpio. I want to restore just some directory from this device but I do not know the command ??
other question
what is the best cpio command to take more than 8 GB data ?
thanks
Alice (1 Reply)
Hi. I have a situation here where I need to backup a users' home directory and restore onto another server. The issue here is that both servers have different operating systems and I am looking for advices on how to proceed.
The source server operating system is Tru64 v5.1, and here's the output... (1 Reply)
Hi,
I use following command to restore data from my cpio tape archive:
$cpio -icvd < /dev/rct0
But this'll restore all tape contents to the current path, what if I want only selected files from the tape, suppose I want
/home/compdir/home2/Rev83/data/PL/01/*.*
files to be restored... (8 Replies)
Hi,
under unix aix , i had to put a catostrophic patch from an editor ...
i had first made a cpio backup
connected root
cd /application
find . –print | cpio –ocvBm > /sauvegarde/sauvegarde.cpio
Does someone know the command to restore my cpio backup ?
thanks in advandce to everyone
... (7 Replies)
Hello Every one,
I want to back up all passwd files to /xyz/passfiles.cpio
and Then restore them to /abc directory.
Here is what I wrote:
find / -name passwd | cpio -oc > /tmp/passwd.cpio
and to restore
cd abc
cpio -ium < /tmp/passwd.cpio
I can not find the files restored to /abc... (2 Replies)
Hello folks, one of the RAID drives in our SCO system crashed recently and being hot swap it was replaced.
Problem was that on boot it stops at:
Checking protected password and protected subsystem databases....
First I did #authck -a and checked /etc/auth/system/ttys as per instructions in a... (7 Replies)
Please note that using the command cpio to back up to tape was successful. Used the below command:
time find /accts -print | cpio -oa --block-size=512 --format=newc --verbose -O /dev/nst0
I'm trying to restore from tape of a particular file and having issues. Below is the command to restore... (7 Replies)
Discussion started by: isoabv
7 Replies
LEARN ABOUT BSD
fastboot
REBOOT(8) System Manager's Manual REBOOT(8)NAME
reboot - stopping and restarting the system
SYNOPSIS
/sbin/reboot [ -lqnhdarsfRD ]
/sbin/halt [ -lqndars ]
/sbin/fastboot [ -lqndarsRD ]
DESCRIPTION
2.11BSD is started by placing it in memory at location zero and transferring to its entry point. Since the system is not reentrant, it is
necessary to read it in from disk or tape each time it is to be boot strapped.
Rebooting a running system: When the system is running and a reboot is desired, shutdown(8) is normally used to stop time sharing and put
the system into single user mode. If there are no users then /sbin/reboot can be used without shutting the system down first.
Reboot normally causes the disks to be synced and allows the system to perform other shutdown activities such as resynchronizing hardware
time-of-day clocks. A multi-user reboot (as described below) is then initiated. This causes a system to be booted and an automatic disk
check to be performed. If all this succeeds without incident, the system is then brought up for multi-user operation.
Options to reboot are:
-l Don't try to tell syslogd(8) what's about to happen.
-q Reboot quickly and ungracefully, without shutting down running processes first.
-n Don't sync before rebooting. This can be used if a disk or the processor is on fire.
-h Don't reboot, simply halt the processor.
-d Dump memory onto the dump device, usually part of swap, before rebooting. The dump is done in the same way as after a panic.
-a Have the system booter ask for the name of the system to be booted, rather than immediately booting the default system (/unix).
-r Mount the root file system as read only when the system reboots. This is not supported by the kernel in 2.11BSD.
-s Don't enter multi-user mode after system has rebooted - stay in single user mode.
-f Fast reboot. Omit the automatic file system consistency check when the system reboots and goes multi-user. This is accomplished by
passing a fast reboot flag on to the rebooting kernel. This currently prevents the use of -f flag in conjunction with the -h (halt)
flag.
-D Set the autoconfig(8) debug flag. This is normally not used unless one is debugging the autoconfig program.
-R Tells the kernel to use the compiled in root device. Normally the system uses the device from which it was booted as the
root/swap/pipe/dump device.
Reboot normally places a shutdown record in the login accounting file /usr/adm/wtmp. This is inhibited if the -q or -n options are
present. Note that the -f (fast reboot) and -n (don't sync) options are contradictory; the request for a fast reboot is ignored in this
case.
Halt and fastboot are synonymous with ``reboot -h'' and ``reboot -f'', respectively.
Power fail and crash recovery: Normally, the system will reboot itself at power-up or after crashes if the contents of low memory are
intact. An automatic consistency check of the file systems will be performed, and unless this fails, the system will resume multi-user
operations.
SEE ALSO autoconfig(8), sync(2), utmp(8), shutdown(8), syslogd(8)3rd Berkeley Distribution May 24, 1996 REBOOT(8)