Sponsored Content
Top Forums UNIX for Advanced & Expert Users Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)? Post 302460765 by radoulov on Thursday 7th of October 2010 01:52:26 PM
Old 10-07-2010
Please read the rules!
No duplicate posting!
Continue here.

Thank you!
 

9 More Discussions You Might Find Interesting

1. BSD

Mount Fat32,ext3

Hello All, How can i mount ext3 and Fat partition in FreeBSD 6.0 (0 Replies)
Discussion started by: jaibw
0 Replies

2. Solaris

How can I mount a ufs filesystem on a solaris 10 sparc onto a Linux server

Hi there, I am trying to mount a SAN volume (which is mapped to solaris sparc) partitioned with ufs filesystem onto a linux (intel processor 64bit) server. *I have re-compiled the linux kernel t support ufs fstype with ro mount support. filesystem on solaris:... (3 Replies)
Discussion started by: ilan
3 Replies

3. Solaris

Solaris 10 10/08 sparc + iSCSI

hi, I have installed Solaris 10 10/08 on sparc machine. I would like to configure iSCSI on that to mount SAN Volumes. Is there any need to install any additional patches for iSCSI to work. Thanks, Prashant. (4 Replies)
Discussion started by: prashantbhushan
4 Replies

4. Solaris

Iscsi - target + initiator on the same host.

Hi all iscsiadm / iscsitadm. Ive created two devices on a host. # iscsitadm list target Target: 1-disk0 iSCSI Name: iqn.1986-03.com.sun:02:f105ddf3-52a4-ed7a-9590-c3d354b8fc32.1-disk0 Connections: 1 Target: 1-disk1 iSCSI Name:... (0 Replies)
Discussion started by: sbk1972
0 Replies

5. UNIX for Advanced & Expert Users

LTO2 tape drive as iSCSI target

I'm using Bacula as my backup system, with full backups going to an LTO2 tape drive, while differentials and incrementals go to a disk array on my main server, babylon4. The tape drive is currently attached to a separate machine, because babylon4 does not have a SCSI controller, nor a free PCI-X... (0 Replies)
Discussion started by: Phil Stracchino
0 Replies

6. Solaris

Can You Mount FAT32 iSCSI Target in Solaris 10 (sparc)?

I get "mount: I/O error" when trying to mount an existing FAT32 iSCSI target. I also tried formatting the iSCSI target with fdisk and got fdisk: "Error in ioctl DKIOCSMBOOT" Details -- According to the format command, the whole disk is allocated to slice 6 and /dev/rdsk shows this as:... (0 Replies)
Discussion started by: ctafret
0 Replies

7. HP-UX

After adding new iscsi target port, still the session state of that target port is showing offline

Hi, I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result ... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies

8. HP-UX

Unable to delete iscsi target

Hi Please can someone give me a hint on this, when I list the targets, I see two o them: #iscsiutil -p Operational Target Information ------------------------------ Target # 1 ----------- Target Name : iqn.1992-08.com.netapp:sn.142241859 Target Alias ... (2 Replies)
Discussion started by: fretagi
2 Replies

9. Linux

How to boot iSCSI target from console linux?

I need boot any images from iSCSI and I'd like to boot from linux console of a previous LiveCD booted. Is possible, without gpxe, ipxe firmware or similar? With a simple iSCSI initiator for example? (1 Reply)
Discussion started by: spark2k06
1 Replies
OCF_HEARTBEAT_ISCSI(7)						OCF resource agents					    OCF_HEARTBEAT_ISCSI(7)

NAME
ocf_heartbeat_iscsi - Manages a local iSCSI initiator and its connections to iSCSI targets SYNOPSIS
iscsi [start | stop | status | monitor | validate-all | methods | meta-data] DESCRIPTION
OCF Resource Agent for iSCSI. Add (start) or remove (stop) iSCSI targets. SUPPORTED PARAMETERS
portal The iSCSI portal address in the form: {ip_address|hostname}[":"port] (required, string, no default) target The iSCSI target IQN. (required, string, no default) discovery_type Target discovery type. Check the open-iscsi documentation for supported discovery types. (optional, string, default sendtargets) iscsiadm open-iscsi administration utility binary. (optional, string, default iscsiadm) udev If the next resource depends on the udev creating a device then we wait until it is finished. On a normally loaded host this should be done quickly, but you may be unlucky. If you are not using udev set this to "no", otherwise we will spin in a loop until a timeout occurs. (optional, string, default yes) SUPPORTED ACTIONS
This resource agent supports the following actions (operations): start Starts the resource. Suggested minimum timeout: 120. stop Stops the resource. Suggested minimum timeout: 120. status Performs a status check. Suggested minimum timeout: 30. monitor Performs a detailed status check. Suggested minimum timeout: 30. Suggested interval: 120. validate-all Performs a validation of the resource configuration. Suggested minimum timeout: 5. methods Suggested minimum timeout: 5. meta-data Retrieves resource agent metadata (internal use only). Suggested minimum timeout: 5. EXAMPLE
The following is an example configuration for a iscsi resource using the crm(8) shell: primitive example_iscsi ocf:heartbeat:iscsi params portal=string target=string op monitor depth="0" timeout="30" interval="120" SEE ALSO
http://www.linux-ha.org/wiki/iscsi_(resource_agent) AUTHOR
Linux-HA contributors (see the resource agent source for information about individual authors) resource-agents 1.0.3 07/05/2010 OCF_HEARTBEAT_ISCSI(7)
All times are GMT -4. The time now is 08:07 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy