Yes, thanks, I didn't pay attention! But I think my loop ensures it is a file, not a directory. I mean, it will exit in your command if it is a directory. Maybe we have to know what he really needs.
This will make sure at least one file will be executed. With corrections:
Code:
ls --file-type -t | grep -v /$ | while read file; do
if [ -s $file ]; then
COMMAND YOU WANT TO RUN ON $file
break
fi
done
:mad: I did this the other day but one of my support personnel removed my history so i could call it back up to remeber the exact command since i am air-headed at times. I am trying to take a 30 MEG file off the system and drop it to tape then i want to make the file go back to being 0 bytes so... (1 Reply)
Hi all,
Does anybody know or guide me on how to remove the first N bytes and the last N bytes from a binary file? Is there any AWK or SED or any command that I can use to achieve this?
Your help is greatly appreciated!!
Best Regards,
Naveen. (1 Reply)
What is the easiest way to inspect the bytes stored in a file?
Ideally, If my file was 10 bytes each of which had only the high bit set, I'd be able to browse for it and get output like this:
01 - 10000000
02 - 10000000
03 - 10000000
04 - 10000000
05 - 10000000
06 - 10000000
07 -... (7 Replies)
While running script I am getting an error like
Few lines in data are not being processed.
After googling it I came to know that adding such line would give some memory to it
ini_set("memory_limit","64M");
my input file size is 1 GB.
Is that memory limit is based on RAM we have on... (1 Reply)
Hi,
If I want to copy a 1024 byte data stream in to the target location in 3-bytes chunk, I guess I can use the following script.
dd bs=1024 count=3 if=/src of=/dest
But, I would like to know, how to do it via a C program. I have tried this with memcpy(), that did not help. (3 Replies)
Hello guys. I really hope someone will help me with this one..
So, I have to write this script who:
- creates a file home/student/vmdisk of 10 mb
- formats that file to ext3
- mounts that partition to /mnt/partition
- creates a file /mnt/partition/data. In this file, there will... (1 Reply)
hello,
suppose, entered input is of 1-40 bytes, i need it to be converted to 40 bytes exactly.
example: if i have entered my name anywhere between 1-40 i want it to be stored with 40 bytes exactly.
enter your name:
donald duck (this is of 11 bytes)
expected is as below - display 11... (3 Replies)
is there a better way to do this:
head -c 10000k /var/dump.log | head -c 6000k
unfortunately, the "-c" option is not available on sun solaris. so i'm looking at "dd". but i dont know how to use it to achieve the same exact goal as the above head command.
this needs to work on both solaris... (5 Replies)
Hi Expert,
I'm having grub problem here:
grub> root
(hd0,0): Filesystem type is ext2
grub> setup
Error 11 : Unrecognized Device String
I try install boot loader follow the instruction from 26.2. Booting into Rescue Mode
It says : select Continue, it attempts to mount your file... (4 Replies)
Discussion started by: justbow
4 Replies
LEARN ABOUT FREEBSD
atf-sh
ATF-SH(1) BSD General Commands Manual ATF-SH(1)NAME
atf-sh [-s shell] -- interpreter for shell-based test programs
SYNOPSIS
atf-sh script
DESCRIPTION
atf-sh is an interpreter that runs the test program given in script after loading the atf-sh(3) library.
atf-sh is not a real interpreter though: it is just a wrapper around the system-wide shell defined by ATF_SHELL. atf-sh executes the inter-
preter, loads the atf-sh(3) library and then runs the script. You must consider atf-sh to be a POSIX shell by default and thus should not
use any non-standard extensions.
The following options are available:
-s shell Specifies the shell to use instead of the value provided by ATF_SHELL.
ENVIRONMENT
ATF_LIBEXECDIR Overrides the builtin directory where atf-sh is located. Should not be overridden other than for testing purposes.
ATF_PKGDATADIR Overrides the builtin directory where libatf-sh.subr is located. Should not be overridden other than for testing purposes.
ATF_SHELL Path to the system shell to be used in the generated scripts. Scripts must not rely on this variable being set to select a
specific interpreter.
EXAMPLES
Scripts using atf-sh(3) should start with:
#! /usr/bin/env atf-sh
Alternatively, if you want to explicitly choose a shell interpreter, you cannot rely on env(1) to find atf-sh. Instead, you have to hardcode
the path to atf-sh in the script and then use the -s option afterwards as a single parameter:
#! /path/to/bin/atf-sh -s/bin/bash
ENVIRONMENT
ATF_SHELL Path to the system shell to be used in the generated scripts.
SEE ALSO atf-sh(3)BSD September 27, 2014 BSD