I havet two books, one in Swedish, the other in English.
Two text files. I want to combine them into one, with each sentence having it's translation next to it.
------------
Text file one.
Example sentence in English. Example 2 sentence 2 in English 2.
--------------
Text file two.
... (2 Replies)
Hello,
I have two files:
File1:
a
b
c
d
File2:
b
c
e
I need 'e' as output....
Thanks..
---------- Post updated at 12:16 PM ---------- Previous update was at 12:15 PM ---------- (1 Reply)
Hi,
I want to concatenate the texts in the file but there are different scenario's.
Ist Scenario.
The contents of file has id`language,sequence number,text,language
Here id`language is a key pair to identify the correct language.
Sequnce number is the order the text being inserted.
Text... (3 Replies)
Hi all,
I've the following hostnames & ip addresses saved in host_ip.txt
Based on this list, I need to create the following script.
where by HH is a hostname
and XXXX is an ip address
So the final output would be something like this.
Currently, I'm doing it manually, replace, copy... (3 Replies)
Hi,
I have a file with texts shown below,
<2013 abc
<2013 start
request pdu
dot1q
end pdu
response pdu
dot1q
end pdu
am searching for the text "dot1q" , when it matches in the file , i need the contents between "<2013 start" and "end pdu". Can some one help on this ?
... (5 Replies)
Hi,
i have two variables i.e
lck_ckm_customer=ckm_customer and(present in some script A)
table=ckm_customer(present in script B)
in script B i am executing this part
if ; then
---
----
----
fi
Now, while comparing in my log file i am getting this result
if
but i... (2 Replies)
Discussion started by: gnnsprapa
2 Replies
8. Post Here to Contact Site Administrators and Moderators
Can you add hover texts (alt-texts) to icons? It is not always obvious what each of them mean just by looking at them. Sometimes it is clear from the url it points to, but for accessibility reasons alone it would be good to have alt-texts as a standard. (1 Reply)
Hi Gurus,
I have requirement to compare current result with previous reuslt.
The sample case is below.
1 job1 1
1 job2 2
1 job3 3
2 job_a1 1
2 job_a2 2
2 job_a3 3
3 job_b1 1
3 job_b2 2
for above sample file, GID is group ID, for input line, the job run... (1 Reply)
is there any way to align my text so every column begins on the same line as the previous line?
here's my command:
printf "THEN ( ${SEARCHPATTB} = Hour = ${CALTOTB} ) %8s => %8s NOW ( ${SEARCHPATT} = Hour = ${CALTOT} ) %7s => %7s Reduced By: %7s -${RESULT}"\\n
output i'm currently getting... (2 Replies)
Discussion started by: SkySmart
2 Replies
LEARN ABOUT DEBIAN
bup-margin
bup-margin(1) General Commands Manual bup-margin(1)NAME
bup-margin - figure out your deduplication safety margin
SYNOPSIS
bup margin [options...]
DESCRIPTION
bup margin iterates through all objects in your bup repository, calculating the largest number of prefix bits shared between any two
entries. This number, n, identifies the longest subset of SHA-1 you could use and still encounter a collision between your object ids.
For example, one system that was tested had a collection of 11 million objects (70 GB), and bup margin returned 45. That means a 46-bit
hash would be sufficient to avoid all collisions among that set of objects; each object in that repository could be uniquely identified by
its first 46 bits.
The number of bits needed seems to increase by about 1 or 2 for every doubling of the number of objects. Since SHA-1 hashes have 160 bits,
that leaves 115 bits of margin. Of course, because SHA-1 hashes are essentially random, it's theoretically possible to use many more bits
with far fewer objects.
If you're paranoid about the possibility of SHA-1 collisions, you can monitor your repository by running bup margin occasionally to see if
you're getting dangerously close to 160 bits.
OPTIONS --predict
Guess the offset into each index file where a particular object will appear, and report the maximum deviation of the correct answer
from the guess. This is potentially useful for tuning an interpolation search algorithm.
--ignore-midx
don't use .midx files, use only .idx files. This is only really useful when used with --predict.
EXAMPLE
$ bup margin
Reading indexes: 100.00% (1612581/1612581), done.
40
40 matching prefix bits
1.94 bits per doubling
120 bits (61.86 doublings) remaining
4.19338e+18 times larger is possible
Everyone on earth could have 625878182 data sets
like yours, all in one repository, and we would
expect 1 object collision.
$ bup margin --predict
PackIdxList: using 1 index.
Reading indexes: 100.00% (1612581/1612581), done.
915 of 1612581 (0.057%)
SEE ALSO bup-midx(1), bup-save(1)BUP
Part of the bup(1) suite.
AUTHORS
Avery Pennarun <apenwarr@gmail.com>.
Bup unknown-bup-margin(1)