hi,
i m tryin to learn ldap.
but its not getting configured.
the error msg it shows is:
LDAP configure error: BDB/HDB : Berkeley DB version incompatibe.
The BDB version i have installed is bdb4.2.52 and the ldap version is openldap-2.3.12.
my machine is running on red hat linux 9.
Why... (1 Reply)
My computer which uses scoUNIX, has an internal scsi tape backup. It will
no longer backup . It posts this message Notice :Stp tape 0 device 46/0
offline. This has been discussed before by the forum and I'd appreciate any
help that any expert could provide for me for a step wise approach to... (0 Replies)
My tape drive is not backing up my data. This is the message that comes up as the computer starts up each morning. Notice Stp:SCSI tape 0 device 46/0 offline. The computer is equipped with a Seagate STD 24000N internal tape drive and the green indicator light on it continuously is on but the amber... (0 Replies)
I am having trouble understanding the difference between a passthrough device and a named device and when you would use one or the other to access equipment.
As an example, we have a tape library and giving the command
"camcontrol devlist" gives the following output:
akx# camcontrol... (1 Reply)
Hello,
I attached a tape drive to one of my partitions but i cannot find the device.
I run the command lsdev|grep rmt but i dont get anything in return.
When i run lsslot -c slot i can see the slot number and the device that belongs to the tape drive but i cannot find any rmt files in /dev.... (6 Replies)
Help Please!
I picked up a V440 and it has 4 disks. I installed Solaris fine to disk 3, but I cannot see the other disks in Solaris.
I have run probe-scsi-all from OBP and I see the other disks and they have names in devalias AFAIK. It's just in Solaris they do not appear. I have run... (6 Replies)
Hi have a solaris server with the following IP 192.168.0.85, but anybody can login in using 172.19.0.85, and the ifconfigcommand does not show the 172.19.05 .
# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask... (6 Replies)
I have kali running on vbox as :-
/etc/network/interfaces
ifup eth0 gives me
tpcdump (0 Replies)
Discussion started by: lazerz
0 Replies
LEARN ABOUT SUSE
scsi_address
scsi_address(9S) Data Structures for Drivers scsi_address(9S)NAME
scsi_address - SCSI address structure
SYNOPSIS
#include <sys/scsi/scsi.h>
INTERFACE LEVEL
Solaris architecture specific (Solaris DDI)
DESCRIPTION
A scsi_address structure defines the addressing components for a SCSI target device. The address of the target device is separated into two
components: target number and logical unit number. The two addressing components are used to uniquely identify any type of SCSI device;
however, most devices can be addressed with the target component of the address.
In the case where only the target component is used to address the device, the logical unit should be set to 0. If the SCSI target device
supports logical units, then the HBA must interpret the logical units field of the data structure.
The pkt_address member of a scsi_pkt(9S) is initialized by scsi_init_pkt(9F).
STRUCTURE MEMBERS
scsi_hba_tran_t *a_hba_tran; /* Transport vectors for the SCSI bus */
ushort_t a_target; /* SCSI target id */
uchar_t a_lun; /* SCSI logical unit */
a_hba_tran is a pointer to the controlling HBA's transport vector structure. The SCSA interface uses this field to pass any transport
requests from the SCSI target device drivers to the HBA driver.
a_target is the target component of the SCSI address.
a_lun is the logical unit component of the SCSI address. The logical unit is used to further distinguish a SCSI target device that supports
multiple logical units from one that does not. The makecom(9F) family of functions use the a_lun field to set the logical unit field in the
SCSI CDB, for compatibility with SCSI-1.
SEE ALSO makecom(9F), scsi_init_pkt(9F), scsi_hba_tran(9S), scsi_pkt(9S)
Writing Device Drivers
SunOS 5.10 30 Aug 1995 scsi_address(9S)