08-24-2010
Hey Corona688,
You were right, the driver '8139too' was blacklisted from modprobe, i don't know the reason. I commented ('#') it and rebooted, and i got it working. with some issues, but working. (Now there's no 'eth0' device, but 'eth1' and 'eth2').
Thank you very much.
10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
I am using Slackware 7 on my IBM Thinkpad. I am unable to configure it to display a graphical environment. Typing startx usually generates a few errors. The system, however, does boot into the shell environment without any issues or problems. I have been able to setup Slackware 7 successfully... (2 Replies)
Discussion started by: adrienb
2 Replies
2. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
Hi,
I'm looking for a command to be able to list all my network cards available on my server.
With the command "ifconfig - a", I can only see to configured network card(s)
Any idea ? :confused:
Thanks a lot for your help,
Fabien (5 Replies)
Discussion started by: unclefab
5 Replies
5. AIX
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies
6. Solaris
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies
7. Solaris
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies
8. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
9. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
10. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
LEARN ABOUT PHP
tc-matchall
Match-all classifier in tc(8) Linux Match-all classifier in tc(8)
NAME
matchall - traffic control filter that matches every packet
SYNOPSIS
tc filter ... matchall [ skip_sw | skip_hw ] [ action ACTION_SPEC ] [ classid CLASSID ]
DESCRIPTION
The matchall filter allows to classify every packet that flows on the port and run a action on it.
OPTIONS
action ACTION_SPEC
Apply an action from the generic actions framework on matching packets.
classid CLASSID
Push matching packets into the class identified by CLASSID.
skip_sw
Do not process filter by software. If hardware has no offload support for this filter, or TC offload is not enabled for the inter-
face, operation will fail.
skip_hw
Do not process filter by hardware.
EXAMPLES
To create ingress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle ffff: ingress
tc filter add dev eth1 parent ffff:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an ingress qdisc with handle ffff: on device eth1 where the second command attaches a matchall filters on it that
mirrors the packets to device eth2.
To create egress mirroring from port eth1 to port eth2:
tc qdisc add dev eth1 handle 1: root prio
tc filter add dev eth1 parent 1:
matchall skip_sw
action mirred egress mirror
dev eth2
The first command creats an egress qdisc with handle 1: that replaces the root qdisc on device eth1 where the second command attaches a
matchall filters on it that mirrors the packets to device eth2.
To sample one of every 100 packets flowing into interface eth0 to psample group 12:
tc qdisc add dev eth0 handle ffff: ingress
tc filter add dev eth0 parent ffff: matchall
action sample rate 100 group 12
SEE ALSO
tc(8),
iproute2 21 Oct 2015 Match-all classifier in tc(8)