08-24-2010
Good call, Corona688!
I extracted the card from the mother board and the Ethernet card chipset is a RealTek 8139A (RTL8139A), but lspci shows it as a 'Honeywell' and, as i already said, doesn't recognize it.
What can be happening? How do i get it to work?
Thank you very much.
10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
I am using Slackware 7 on my IBM Thinkpad. I am unable to configure it to display a graphical environment. Typing startx usually generates a few errors. The system, however, does boot into the shell environment without any issues or problems. I have been able to setup Slackware 7 successfully... (2 Replies)
Discussion started by: adrienb
2 Replies
2. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
Hi,
I'm looking for a command to be able to list all my network cards available on my server.
With the command "ifconfig - a", I can only see to configured network card(s)
Any idea ? :confused:
Thanks a lot for your help,
Fabien (5 Replies)
Discussion started by: unclefab
5 Replies
5. AIX
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies
6. Solaris
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies
7. Solaris
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies
8. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
9. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
10. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
LEARN ABOUT REDHAT
axnet_cs
AXNET_CS(4) Kernel Interfaces Manual AXNET_CS(4)
NAME
axnet_cs - Asix AX88190 chipset PCMCIA Ethernet Driver
SYNOPSIS
insmod axnet_cs.o [pc_debug=n] [irq_list=i,j,...]
DESCRIPTION
Axnet_cs is a driver for PCMCIA ethernet cards based on the Asix AX88190 chipset. These cards are mostly NE2000 compatible but have sev-
eral bugs that are sufficiently tricky to work around that a separate driver was deemed necessary. When this driver is bound to a card, it
allocates the next available ethernet device (eth0..eth#). This device name will be reported in the kernel log file, and passed on to
cardmgr(8).
PARAMETERS
pc_debug=n
Selects the PCMCIA debugging level. This parameter is only available if the module is compiled with debugging enabled. A non-zero
value enables debugging.
irq_list=i,j,...
Specifies the set of interrupts that may be allocated by this driver.
DIAGNOSTICS
axnet_cs: this is not an AX88190 card!
Indicates that this card is probably a normal NE2000 compatible card, which requires the pcnet_cs driver.
eth#: interrupt(s) dropped!
Indicates that the driver did not receive an interrupt notification for some reason. The driver will poll the card (with a signifi-
cant performance penalty) if the problem persists. The most likely cause is an interrupt conflict and/or host bridge configuration
problem.
AUTHOR
David Hinds - dahinds@users.sourceforge.net
SEE ALSO
cardmgr(8), pcmcia(5).
pcmcia-cs 2001/08/17 12:51:58 AXNET_CS(4)