I'm having troubles with Slackware 13.1 and network cards.
I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the two cards:
But, when i run ifconfig, i only can see the Intel on-board card as eth0.
I remember that slackware 12.0, 12.1 and even 12.2 automatically recognized and configured the network cards, but this version seems to work different.
Could someone help me to configure them? I'm loosing my head trying to figure out what's wrong with the system...
Thanks in advance.
My /etc/rc.d/rc.inet1.conf looks like the following:
When i run 'dmesg' it outputs the following:
Please, help!
I am using Slackware 7 on my IBM Thinkpad. I am unable to configure it to display a graphical environment. Typing startx usually generates a few errors. The system, however, does boot into the shell environment without any issues or problems. I have been able to setup Slackware 7 successfully... (2 Replies)
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Hi,
I'm looking for a command to be able to list all my network cards available on my server.
With the command "ifconfig - a", I can only see to configured network card(s)
Any idea ? :confused:
Thanks a lot for your help,
Fabien (5 Replies)
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
LEARN ABOUT NETBSD
sm
SM(4) BSD Kernel Interfaces Manual SM(4)NAME
sm -- SMC91Cxx-based Ethernet interfaces device driver
SYNOPSIS
sm0 at isa? port 0x300 irq 10
sm* at mhzc?
sm* at pcmcia? function ?
sm* at nubus?
DESCRIPTION
The sm device driver supports SMC91C9x-based and SMC91C1xx-based Ethernet interfaces.
The ISA attachment of the sm driver supports any SMC91C9x-based Ethernet interface on the ISA bus, including the EFA Info*Express SVC VLB
interface, and the on-board SMC91C9x Ethernet found in many embedded PCs and laptop docking stations.
The mhzc attachment of the sm driver supports the Megahertz combo Ethernet and modem card.
The PCMCIA attachment of the sm driver supports Megahertz X-JACK Ethernet cards.
The nubus attachment of the sm driver supports SMC-based Ethernet cards for the macintosh.
MEDIA SELECTION
The SMC91C1xx supports the MII interface and so the list of supported media depends on several factors, including which PHY is attached. The
SMC91C9x supports AUI and UTP media types.
To enable the AUI media, select the 10base5 or aui media type with ifconfig(8)'s media directive. To select UTP, select the 10baseT or utp
media type.
ifconfig(8)'s -m option will display the full list of supported media directives for a particular configuration.
DIAGNOSTICS
sm0: unable to read MAC address from CIS This indicates that the Ethernet address, which is stored in the CIS information on the Megahertz
X-JACK PCMCIA Ethernet card, is corrupted.
SEE ALSO ifmedia(4), intro(4), isa(4), mhzc(4), mii(4), pcmcia(4), ifconfig(8)BSD November 10, 1997 BSD