|
|
Sponsored Content
Operating Systems
SCO
declare disk driver for IDE hard disk
Post 302447019 by ccc on Friday 20th of August 2010 01:56:37 PM
08-20-2010
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Does anyone know of any commands that offer the same sort of facilities of scandisk on windows. My Linux server (Mandrake 6.2) keeps crashing and gives hard disk errors when I reboot. I've used fcsk to fix any problems that arise but when I use dumpe2fs to display disk information it says that... (1 Reply)
Discussion started by: DGM
1 Replies
2. UNIX Desktop Questions & Answers
I have a cuestion. How Can I to add other hard disk to my computer? I need to configurate anyone? (4 Replies)
Discussion started by: hmaraver
4 Replies
3. UNIX for Dummies Questions & Answers
Hi everybody,
I have Ultra 5 operating station, I fixed a new 80 GB HDD, when Iam installing Solaries "2.6, veeeeery old" the system see the hard disk as only 8002 MB "8GB" what can I do so the system will consider the whole capacity of the HDD. any capacity higher then 8 GB will be seen as 8 GB... (4 Replies)
Discussion started by: adol3
4 Replies
4. AIX
Hi,
I'm getting the errors below in the errpt report for a IBM Blade server. I'm guessing there's a problem with one of the disks but don't know how I can confirm this. Can anyone offer any suggestions?
Regards
Gareth (4 Replies)
Discussion started by: m223464
4 Replies
5. Filesystems, Disks and Memory
Wellcomes All,
some times ago I 've installed a Debian ditribution on an Hard Disk who was set as Primary Master. Few days ago, I 've decided to install another Hard Disk with a different Operating System. When I did that, I turned off the old hard disk, and I mouted the new one on the Primary IDE... (1 Reply)
Discussion started by: thekarsillo
1 Replies
6. Solaris
Hi experts,
i have added a new disk to my ultra 10 system, after that i am unable to boot the system, its not booting from disk neither from cd.
please help!
Regards (16 Replies)
Discussion started by: kumarmani
16 Replies
7. UNIX for Dummies Questions & Answers
:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on
"The following file systems are low, and could adversely affect server performance:
File system /: 99%full"
Can some one please explain... (9 Replies)
Discussion started by: mannyisme
9 Replies
8. Filesystems, Disks and Memory
Hello,
I wanted to share an experience I had today which was quite a learning experience and perhaps useful for others who may run into the issue at some point in the future.
Basically, the scenario involves a OS which was installed on a machine which hardware-wise, had a SATA Drive. The... (0 Replies)
Discussion started by: septima.pars
0 Replies
9. UNIX Desktop Questions & Answers
Hi there! I am installing Unixware 7.1 to a new server. We usually use SCSI hard for this but since this will be used only for testing, I decided to use an 80GB IDE hard disk. I was able to successfully load the unix but found out that the 80GB hard disk was not maximized. The total hard disk... (1 Reply)
Discussion started by: limpinmd
1 Replies
10. Linux
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Discussion started by: shen747
23 Replies
LEARN ABOUT NETBSD
stpcide
STPCIDE(4) BSD Kernel Interfaces Manual STPCIDE(4) NAME
stpcide -- STMicroelectronics STPC IDE disk controllers driver SYNOPSIS
stpcide* at pci? dev ? function ? flags 0x0000 DESCRIPTION
The stpcide driver supports the STMicroelectronics STPC x86 SoC internal IDE controllers, and provides the interface with the hardware for the ata(4) driver. The driver features DMA mode 2 and PIO mode 4 transfer speeds. The 0x0002 flag forces the stpcide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debug- ging aid, or to work around problems where the IDE controller is wired up to the system incorrectly. SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4) BUGS
The timings used for the DMA and PIO modes are for STPC Atlas and its siblings with their PCI clock configured at 33 MHz. Other speeds including the STPC Vega Ultra-IDE controller will need adjustments. BSD
October 31, 2003 BSD