SUN Netra 240 Boot error Post: 302443814

Sponsored Content

Operating Systems Solaris SUN Netra 240 Boot error Post 302443814 by notreallyhere on Tuesday 10th of August 2010 06:11:13 AM

08-10-2010

Registered User

Hi

I have been having the same issue with one of our remote systems.

Code:

{1} ok boot
Probing system devices
Probing memory
ChassisSerialNumber xxxxxx 
Probing I/O buses

Sun Fire V240, No Keyboard
Copyright 2007 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.22.33, 4096 MB memory installed, Serial #xxxxxx.
Ethernet address xxxxxx, Host ID: xxxxxxx.



Rebooting with command: boot                                          
Boot device: disk  File and args: 
Boot load failed.
The file just loaded does not appear to be executable.

Tried all of the previously mentioned things as well.
Tried booting from different disks on that system or the mirrors in place but to no avail.

A few days prior to running into this issue I did successfully power on and boot the system. It was also shut down gracefully after that and stayed down until I tried to bring it up again three days afterwards.

When booting from cdrom I could mount the different slices on all disks and see their contents.
Also, I got this error when booting from cdrom:

Code:

WARNING: /pci@1c,600000/scsi@2/sd@1,0 (sd1):
        Error for Command: load/start/stop         Error Level: Informational
        Requested Block: 0                         Error Block: 0
        Vendor: SEAGATE                            Serial Number: 0503B9Z8H8  
        Sense Key: Soft Error
        ASC: 0x5d (drive operation marginal, service immediately (failure prediction threshold exceeded)), ASCQ: 0x0, FRU: 0x42

notreallyhere

View Public Profile for notreallyhere

Find all posts by notreallyhere

9 More Discussions You Might Find Interesting

1. Solaris

Netra 240 Hard disk are not detected

Hi All, I have new Netra 240 box which is not detecting its harddisk equiped with itse same har disk are detected when I swap with another machine. Same time If I swap hardisk of other machine to this Netra 240 box, also do not work. I have checked chassis, cabling etc and all looks fine. ...

2. Solaris

sun netra t1

so i've grabbed this sun netra t1 for some small dev work. now obviously i need to install sol10. no problem done it a million times except for the fact that i've never actually done it w/o a term server. so i grab a usb to serial and a serial to rj45 (the one you get in every cisco order.. roll...

3. Solaris

netra 240 difference

Hi, sunfire v240 and netra 240 are looks similar. system board, memory and processors are similar, then why netra 240 called as telco server? can anyone tell the difference. RJS

4. UNIX for Dummies Questions & Answers

Refurbished Netra 240 servers hangs after POST test

Hello everyone, I'm extremely new when it comes to SUN servers so bear with me and hopefully I can describe the issue I have accurately. At work we just received a refurbished SUN Netra 240 server. I was told to change some of the EEprom settings, and to do that I was to use a...

5. Solaris

Unable to access serial port from non-global solaris zone on netra 240

I am trying to use a serial communications device that is connected to /dev/ttyb on a netra 240 server. This is a solaris zone configuration using solaris 10 0910. I am able to access /dev/ttyb from the global zone but not throught he non-global zone. I have enabled all of the tty devices in my...

6. Hardware

POST displays error sparc netra 240

Hi guys, when I power on my sun netra 240 server, it displays these error messages: 1. Notice: cpu 0 has 2048/2048 MB of memory disabled. 2. Error : The following devices are disabled dimm1. Please can anyone be kind enough to explain this for me? Thanks

7. Solaris

Fsck: alignment error Solaris 8, SUN Netra AX11505

Hello all, I recently powered on my Netra AX1105 server only to be greeted with the following error message. I am not sure what to do here, I cant fun fsck on OK prompt.. did ok>boot -r and now it keeps booting from net, then I run ok>boot disk then outputs the following message... and keeps...

8. Solaris

SUn Netra X4200 M2 Drivers

Hi Guys, Could someone please share the dvd/cd that came with server Netra x4200 M2 since it is not more available in Oracle site? Or do you know where I can get that? Thanks!

9. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about...

LEARN ABOUT FREEBSD

halt

REBOOT(8)						    BSD System Manager's Manual 						 REBOOT(8)

NAME

     reboot, halt, fastboot, fasthalt -- stopping and restarting the system

SYNOPSIS

     halt [-lnpq] [-k kernel]
     reboot [-dlnpq] [-k kernel]
     fasthalt [-lnpq] [-k kernel]
     fastboot [-dlnpq] [-k kernel]

DESCRIPTION

     The halt and reboot utilities flush the file system cache to disk, send all running processes a SIGTERM (and subsequently a SIGKILL) and,
     respectively, halt or restart the system.	The action is logged, including entering a shutdown record into the user accounting database.

     The options are as follows:

     -d      The system is requested to create a crash dump.  This option is supported only when rebooting, and it has no effect unless a dump
	     device has previously been specified with dumpon(8).

     -k kernel
	     Boot the specified kernel on the next system boot.  If the kernel boots successfully, the default kernel will be booted on successive
	     boots, this is a one-shot option.	If the boot fails, the system will continue attempting to boot kernel until the boot process is
	     interrupted and a valid kernel booted.  This may change in the future.

     -l      The halt or reboot is not logged to the system log.  This option is intended for applications such as shutdown(8), that call reboot
	     or halt and log this themselves.

     -n      The file system cache is not flushed.  This option should probably not be used.

     -p      The system will turn off the power if it can.  If the power down action fails, the system will halt or reboot normally, depending on
	     whether halt or reboot was called.

     -q      The system is halted or restarted quickly and ungracefully, and only the flushing of the file system cache is performed (if the -n
	     option is not specified).	This option should probably not be used.

     The fasthalt and fastboot utilities are nothing more than aliases for the halt and reboot utilities.

     Normally, the shutdown(8) utility is used when the system needs to be halted or restarted, giving users advance warning of their impending
     doom and cleanly terminating specific programs.

SEE ALSO

     getutxent(3), boot(8), dumpon(8), nextboot(8), savecore(8), shutdown(8), sync(8)

HISTORY

     A reboot utility appeared in Version 6 AT&T UNIX.

BSD
								 October 11, 2010							       BSD