08-05-2010
Ah! Sorry, I misread your post.
If you can't ping or traceroute to this site, but can get to the rest of the world, and since DNS is obviously working, seems the problem might be in your Mac somewhere. I have had problems on my Mac from time to time that required a reboot and it still did not clear until some unknown TTL passed (still have not got a handle on it).
Still, you should either ping and record the route or use traceroute and determine the last IP address you can hop to and then look into that device for the problem. Please post back what device is the last device there the datagram resides.
10 More Discussions You Might Find Interesting
1. IP Networking
If the cable modem that the cable company is using doesn't support unix is there a way around that . Are there drivers I can get online or is there a way to configure redhat lenix (that's what I will be using) to work with the cable modem. Or is there a way to buy a third party cable modem that... (3 Replies)
Discussion started by: gparsons70
3 Replies
2. UNIX for Dummies Questions & Answers
I recently installed Caldera 2.4 (successfully:p ), but I cannot seem to get my cable modem up and running! My ISP is AT&T and I'm using @home. I've tried using DHCP and that didn't work either. I briefly read the cable modem HOWTO, but the lsmod didn't list my network card (3COM). What do I do now? (4 Replies)
Discussion started by: zorro
4 Replies
3. UNIX for Dummies Questions & Answers
Caldera eDesktop 2.4 - Cable Modem
my NIC card has been detected, but funny scenario:
#dmesg
eth0: RealTek rtl8139 Fast Ethernet at 0x2400, IRQ 0, 00:50:ba:43:a0:ef
/*I noticed that it detected the correct module (rtl8139) but I'm using D-Link and not RealTek, which uses the same module.... (1 Reply)
Discussion started by: zorro
1 Replies
4. UNIX for Dummies Questions & Answers
Is anyone using a cable modem with unix and if so does your cable co. support unix or did you get that going on your own and how.
Thank you for all your help. (5 Replies)
Discussion started by: gparsons70
5 Replies
5. IP Networking
I can do all this in windows, but Im trying to run the SuSe 8.0 professional as a gateway. I have the local (private) LAN setup with no problems, but Im having troubles getting it to use DHCP to go out on the external card to the service provider, which only uses Dynamic IP's. WHere, what and how... (3 Replies)
Discussion started by: ftn96
3 Replies
6. UNIX for Dummies Questions & Answers
hi , i have sparc machine , i want to connect my le0 (ethernet interface) directly to cable modem ,
i have created a file resolv.conf,hosts, dhcp.le0,defaultrouter,nisswitch,hostname.le0. i dont know my cable companies <domain name> and <name server assigned to me> , also they even dont know how... (5 Replies)
Discussion started by: raju
5 Replies
7. UNIX for Dummies Questions & Answers
I have a XP computer which is my primary. I recently, well just today installed a old version of Mandrake Linux 6.5 I had laying on a self collecting dust on a old PII 233mhz that had to be vacummed out before I could use it.
I have my XP computer connected by 10/100 NIC to a cable modem. My... (1 Reply)
Discussion started by: garfunkle
1 Replies
8. BSD
hi
I want to setup my cable modem under OpenBSD. I did not configure my network while installing the system.
When I type, I get
# ifconfig -a
lo0 : ....
...
...
rl0 : ....
...
...
vr0 : ...
...
...
I have two network cards (the machine will be a router).
I created... (1 Reply)
Discussion started by: fnoyan
1 Replies
9. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
10. Cybersecurity
hi
im running a web server running, connected to my cable modem, which, as usual, has 2 different network address. one from "outside"(ie from isp), and the
other for the internal network.
im giving a static ip to the server.how do i access this server from outside the network across "the... (2 Replies)
Discussion started by: R00tSc0rpi0n
2 Replies
LEARN ABOUT MOJAVE
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to a network node
SYNOPSIS
traceroute6 [-dIlnNrvU] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
The traceroute6 utility uses the IPv6 protocol hop limit field to elicit an ICMPv6 TIME_EXCEEDED response from each gateway along the path to
some host.
The only mandatory parameter is the destination host name or IPv6 address. The default probe datagram carries 12 bytes of payload, in addi-
tion to the IPv6 header. The size of the payload can be specified by giving a length (in bytes) after the destination host name.
Other options are:
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit, up to 255. The default is 30 hops.
-n Do not resolve numeric address to hostname.
-N Use a packet with no upper layer header for the probes, instead of UDP datagrams.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-connected net-
work, an error is returned. This option corresponds to the SO_DONTROUTE socket option; it can be used to ping a local host through
an interface that has no route through it (e.g., after the interface was dropped by a routing daemon).
-s src Src specifies the source IPv6 address to be used.
-U Use UDP datagrams for the probes. This is the default.
-v Be verbose.
-w waittime
Specify the delay time between probes.
This program prints the route to the given destination and the round-trip time to each gateway, in the same manner as traceroute.
Here is a list of possible annotations after the round-trip time for each gateway:
!N Destination Unreachable - No Route to Host.
!P Destination Unreachable - Administratively Prohibited.
!S Destination Unreachable - Not a Neighbour.
!A Destination Unreachable - Address Unreachable.
! This is printed if the hop limit is <= 1 on a port unreachable message. This means that the packet got to the destination, but
that the reply had a hop limit that was just large enough to allow it to get back to the source of the traceroute6. This was
more interesting in the IPv4 case, where some IP stack bugs could be identified by this behaviour.
RETURN VALUES
The traceroute6 utility will exit with 0 on success, and non-zero on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 utility first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
May 17, 1998 BSD