Hi,
We have a text file which has the following data.
ISA~00~ ~00~ ~ZZ~VISTN ~ZZ~U1CAD ~051227~183
7~U~00200~000011258~0~P~<
GS~FA~EE05J~U1CAD~051227~1831~000011258~X~002002
ST~997~0001
AK1~SH~247
AK2~856~2470001
AK5~A
AK2~856~2470002
AK5~A... (3 Replies)
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
when I do a tape status /dev/rStp0 I get the following on a new tape and I have tried several:
Status : ready beginning-of-tape
soft errors : 0
hard errors: 2
underruns: 5
My BackupEdge has stopped backing up my system because it asks for a new volume yet my total system data is under 20... (5 Replies)
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
We sometime run backups to tape in the background using the cron. Is there a command that will show me how fast the information is being written and or how much data has been written?
I know if we enter the information via the command prompt or smit it shows the speed and amount written. (2 Replies)
Is there a command on AIX that will show the write status of a tape? We have sysback running via a cron job backing up to a tape. I want to be able to check the progress of the backup. I need a command that will show ne the progress of the backup or the speed of the backup while it is taking... (5 Replies)
Do we have a way in solaris to actuallyu check in real time the activity of a tape when it is loaded for backup?
I know mt -f /dev/rmt/0n stat will provide the status. If it's busy, meaning it's currrently on backup mode or someone is using it (fuser -u /dev/rmt/0n)
I wanted to check if the... (3 Replies)
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
LEARN ABOUT BSD
mt
MT(1) General Commands Manual MT(1)NAME
mt - magnetic tape manipulating program
SYNOPSIS
mt [ -f tapename ] command [ count ]
DESCRIPTION
Mt is used to give commands to a magnetic tape drive. If a tape name is not specified, the environment variable TAPE is used; if TAPE
does not exist, mt uses the device /dev/rmt12. Note that tapename must reference a raw (not block) tape device. By default mt performs
the requested operation once. Operations may be performed multiple times by specifying count.
The available commands are listed below. Only as many characters as are required to uniquely identify a command need be specified.
eof, weof
Write count end-of-file marks at the current position on the tape.
fsf Forward space count files.
fsr Forward space count records.
bsf Back space count files.
bsr Back space count records.
rewind Rewind the tape (Count is ignored).
offline, rewoffl
Rewind the tape and place the tape unit off-line (Count is ignored).
status Print status information about the tape unit.
cacheon
Enable the readahead/writebehind cache on the tape unit.
cacheoff
Turn off the readahead/writebehind cache on the tape unit.
Mt returns a 0 exit status when the operation(s) were successful, 1 if the command was unrecognized, and 2 if an operation failed.
The cacheon and cacheoff commands currently only apply to the TMSCP driver and then only for certain drives such as the TU81+. No error is
produced by the TMSCP driver if the cache commands are used. Other drivers will return an error code since they do not recognize the
MTCACHE and MTNOCACHE functions codes. See mtio(4).
FILES
/dev/rmt* Raw magnetic tape interface
SEE ALSO mtio(4), tmscp(4), dd(1), ioctl(2), environ(7)4th Berkeley Distribution December 22, 1995 MT(1)