07-08-2010
Going by that error message, you are using the wrong gateway address. The gateway you have used is not on a directly-connected network, you need to use the next-hop gateway instead.
10 More Discussions You Might Find Interesting
1. IP Networking
I am running RH7.3 on a compaq presario box. The network card is a Linksys one. I am only able to communicate with the local network (only the local IPs are accessible). When I try to ping another box I get a "Connect: Network is unreachable" message. What could be the problem.
Thanks in... (2 Replies)
Discussion started by: skotapal
2 Replies
2. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
3. Red Hat
hi,
i would like to share this
/etc/sysconfig/network-script/route-eth0
GATEWAY0=XXXXXX
NETMASK0=XXXXXX
ADDRESS0=XXXXXXX
a delete route command with "route del -net xxxx...." will work but if the above exist and you reboot the linux then old route will be invoke on that config-route.
... (0 Replies)
Discussion started by: itik
0 Replies
4. Solaris
Hi All,
yesterday I was trying to add a network route to my solaris 8 host using 'route add'. Everytime I tried, I kept getting the response 'network is unreachable'.
I was trying all kinds of different methods, however I eventually got it to work after bouncing the interface that I was... (2 Replies)
Discussion started by: badoshi
2 Replies
5. Solaris
Hi there,
I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far:
# route add... (2 Replies)
Discussion started by: sreiniche
2 Replies
6. IP Networking
I have built a new linux server, via a iLo connection.
and I am trying to connect via my desktop to the server I have just built to the management port eth0 via putty.
Please could some one advise how to connect to this server from my desktop. Do i need to create add a route access on the... (0 Replies)
Discussion started by: venhart
0 Replies
7. Solaris
Please , I have a problem
I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline.
The system is in cluster mode (3.2)
route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51
-------------------
lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies
8. Linux
Assalam o Alaikum!
After configuring and starting service of samba, when I access shared folder from windows XP it gives this error " Network Route was not found".
My server IP 192.168.1.252, client is on same network.
selinux is disabled
smb,conf:
workgroup = WORKGROUP
server string =... (2 Replies)
Discussion started by: ukengr
2 Replies
9. UNIX for Advanced & Expert Users
Hi,
I have installed RHEL4 using vmware workstation..
Host OS: Windows XP
Guest OS: RHEL4
Pls refer step 17 & 18 in below link...
ORACLE-BASE - Red Hat Enterprise Linux 4 and Centos 4 Installation
1) If i choose to assign IP automatically (using DHCP) means, i am able to connect RHEL4... (3 Replies)
Discussion started by: thomasraj87
3 Replies
10. Solaris
Seems to wanboot ok but then fails to connect to server. What do I need to check?
{0} ok boot net - install
Boot device: /pci@300/pci@1/pci@0/pci@1/network@0 File and args: - install
1G link up
<time unavailable> wanboot info: WAN boot messages->console
<time unavailable>... (2 Replies)
Discussion started by: psychocandy
2 Replies
LEARN ABOUT NETBSD
traceroute6
TRACEROUTE6(8) BSD System Manager's Manual TRACEROUTE6(8)
NAME
traceroute6 -- print the route IPv6 packets will take to the destination
SYNOPSIS
traceroute6 [-adIlnrv] [-A as_server] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]
DESCRIPTION
-A Turn on AS# lookups and use the given server instead of the default.
-a Turn on AS# lookups for each hop encountered.
-d Debug mode.
-f firsthop
Specify how many hops to skip in trace.
-g gateway
Specify intermediate gateway (traceroute6 uses routing header).
-I Use ICMP6 ECHO instead of UDP datagrams.
-l Print both host hostnames and numeric addresses. Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
addresses if -n is specified.
-m hoplimit
Specify maximum hoplimit.
-n Do not resolve numeric address to hostname.
-p port
Set UDP port number to port.
-q probes
Set the number of probe per hop count to probes.
-r Bypass the normal routing tables and send directly to a host on an attached network. If the host is not on a directly-attached net-
work, an error is returned. This option can be used to send probes to a local host through an interface that has no route through it
(e.g., after the interface was dropped by route6d(8)).
-s src Src specifies the source IPv6 address to be used.
-v Be verbose.
-w waittime
Specify the delay time between probes.
EXIT STATUS
The traceroute6 command exits 0 on success, and >0 on errors.
SEE ALSO
ping(8), ping6(8), traceroute(8)
HISTORY
The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.
BSD
September 17, 2005 BSD