03-26-2010
If this is a hardware raid 5 then metastat does not come into it does it?
If the volume is not too big for the version of Solaris you are using and you are using the whole volume then might as well newfs s2 and then mount s2.
9 More Discussions You Might Find Interesting
1. High Performance Computing
Dear All,
Can anyone explain about Pros and Cons of SUN and Veritas Cluster ?
Any comparison chart is highly appreciated.
Regards,
RAA (4 Replies)
Discussion started by: RAA
4 Replies
2. Solaris
Dear all,
I have created a shared metaset(500gb) having 3 hosts in which 2 hosts are in cluster and 1 is non cluster. I have taken the ownership in cluster node from non cluster node but the problem is i am unable to mount the file system it is giving error "/dev/md/eccdb-ds/d100 or /eccdb-ds... (1 Reply)
Discussion started by: spandhan
1 Replies
3. Solaris
Dear Cluster Guru,
I had installed sc 3.2 on 2 box sunfire 240 (solaris 10 update 7 ,each node 2 gb ram) and use scsi juke box as share storage .
i had test cluster application :
1. apache HA
2 oracleHA (oracle 9i)
all running well (switch over between... (3 Replies)
Discussion started by: hadibn
3 Replies
4. Solaris
Hi Guys
i have two servers which are n cluster prd1 and prd2.. I already have a metaset configured in it..My job was to create a 1.8 tb LUN in my storage which is having Hardware raid5 pre-configured..i Created 1.8 tb with raid 5 in my storage and it got detected in both t servers prd1... (4 Replies)
Discussion started by: madanmeer
4 Replies
5. Solaris
hi all,
i am using solaris 5.10 on sun blade 150 and i am trying to configure diskset in sun volume manager. When i fire the following command, it says some rpc related error.
bash-3.00# metaset -s kingston -a -h u15_9
metaset: u15_9: metad client create: RPC: Program not registered
how to... (4 Replies)
Discussion started by: kingston
4 Replies
6. Solaris
Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC.
Am thinking how to migrate to sun cluster setup instead.
My plan as follows leave the existing vcs intact as a fallback plan.
Then install and build suncluster on... (5 Replies)
Discussion started by: sparcguy
5 Replies
7. Solaris
Hi,
Is it possible to have a Solaris cluster of 2 nodes at SITE-A using SVM and creating metaset using say 2 LUNs (on SAN). Then replicating these 2 LUNs to remote site SITE-B via storage based replication and then using these LUNs by importing them as a metaset on a server at SITE-B which is... (0 Replies)
Discussion started by: dn2011
0 Replies
8. Solaris
Hello everyone,
Can you please help me understand what happened; here is the problem:
We have a sun cluster composed by two nodes (E4900; sSolaris 9), suddenly one of them were inaccessible by PUTTY, however we were able to ping on it. The cluster haven't basculated and after 20 minutes the... (0 Replies)
Discussion started by: adilyos
0 Replies
9. Solaris
Hello experts -
I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts.
(1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over)
(2) Or should i perform the installation on... (0 Replies)
Discussion started by: NVA
0 Replies
lvmpvg(4) Kernel Interfaces Manual lvmpvg(4)
NAME
lvmpvg - LVM physical volume group information file
SYNOPSIS
DESCRIPTION
is an ASCII file that stores the volume-group information for all of the physical volume groups in the system. The information is stored
in a hierarchical format.
First, it starts with a volume group under which multiple physical volume groups can exist. Under each physical volume group, a list of
physical volumes can be specified. There must be at least one physical volume group in each volume group that appears in this file. The
physical-volume-group name must be unique within the corresponding volume group, although it is permissible to use a common physical volume
group name across different volume groups. There can be as many volume groups in this file as there are in the system.
Instead of using the and commands, the administrator can edit this file to create and extend physical volume groups. However, care must be
taken to ensure that all physical volumes to be included in the file have already been defined in their respective volume groups by previ-
ous use of or
The file format has the following structure. and are keywords that introduce the names of the volume group and physical volume group,
respectively.
pv_path
...
pv_path
...
pv_path
...
The variables are defined as follows:
pv_path The block device path name of a physical volume within the volume group.
pvg_name The name of the physical volume group. It must be unique within the volume group.
vg_name The path name of the volume group.
EXAMPLES
The following example shows an file containing two volume groups: the first containing two physical volume groups, each with two physical
volumes defined in it; the second containing three physical volume groups, each with one physical volume defined in it.
SEE ALSO
vgcreate(1M), vgextend(1M), vgreduce(1M), vgremove(1M), intro(7), lvm(7).
lvmpvg(4)