Sponsored Content
Operating Systems Solaris Sun T5120 hardware RAID question Post 302402606 by incredible on Wednesday 10th of March 2010 07:18:39 AM
Old 03-10-2010
with raidctl -S, you can check the status

eg
Code:
# # raidctl -S

1 "LSI 1030"
c1t1d0 2 0.2.0 0.3.0 1 DEGRADED
0.2.0 GOOD
0.3.0 FAILED


Last edited by incredible; 03-10-2010 at 08:39 AM..
 

9 More Discussions You Might Find Interesting

1. Solaris

how to hardware RAID 1 on T5120

Hi, I have t5120 sparc and I have 2 146 G drives in the system. I will be installing solaris 10 and also want the system mirrored using Hardware RAID "1" The System did come preinstalled as it comes from sun. I did not do much on it. I booted system using boot cdrom -s gave format... (6 Replies)
Discussion started by: upengan78
6 Replies

2. Solaris

How to destroy hardware raid on T5120

Hi, I have problem creating hardware raid on T5120 with 4 disks. After the hardware raid 1 created, then I used the raidctl -l c1t0d0 and raidctl -l c1t2d0 the output of volume c1t0d0 contain disk 0.0.0 0.1.0, also the volume c1t2d0 contain disk 0.0.0 0.1.0 and should be 0.2.0 0.3.0 so I... (15 Replies)
Discussion started by: netlink
15 Replies

3. Solaris

Small issue with Sun Sparc Enterprise T5120

Good Day, We have bought Sun Sparc Enterprise T5120 with pre-installed Solaris 10 Sparc But i need on this server Solaris 9. I have inserted in to DVD-rom (USB DVD-rom) with Solaris 9 for Sparc. Then log into shell and type: reboot -- cdrom. System rebooted and i have this message: ... (3 Replies)
Discussion started by: A.Shalin
3 Replies

4. UNIX for Dummies Questions & Answers

RAID software vs hardware RAID

Hi Can someone tell me what are the differences between software and hardware raid ? thx for help. (2 Replies)
Discussion started by: presul
2 Replies

5. Hardware

Hardware RAID on Sun T2000 Server

Hi All I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command. Following is the hardware RAID output. root@oracledatabaseserver / $ raidctl RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies

6. Hardware

Sun T3-1 hardware RAID

Hi all I've just received my T3-1. It has 8 disks and I would like to configure RAID1 on the disks. The Sun documentation states that you can either use the OpenBoot PROMP utility called Fcode or you can use software via the Solaris OS. The documentation doesn't make it clear if: 1. The... (6 Replies)
Discussion started by: soliberus
6 Replies

7. Solaris

Software RAID on top of Hardware RAID

Server Model: T5120 with 146G x4 disks. OS: Solaris 10 - installed on c1t0d0. Plan to use software raid (veritas volume mgr) on c1t2d0 disk. After format and label the disk, still not able to detect using vxdiskadm. Question: Should I remove the hardware raid on c1t2d0 first? My... (4 Replies)
Discussion started by: KhawHL
4 Replies

8. Solaris

Sun V240 Raid Question

Hi All, I'm new to this site. I have a few question since I'm in the process how to to repair my raid on Sun V240 Server. 1. How can we create RAID in Sun Sparc v240? 2. What utility can help people create RAID in Sun Sparc v240? 3. Do we need any special software to create the... (12 Replies)
Discussion started by: angkor
12 Replies

9. Solaris

Hardware RAID not recognize the new disk [Sun T6320]

We have hardware RAID configured on Sun-Blade-T6320 and one of the disk got failed. Hence we replaced the failed disk. But the hot swapped disk not recognized by RAID. Kindly help on fixing this issue. We have 2 LDOM configured on this server and this server running on single disk. #... (8 Replies)
Discussion started by: rock123
8 Replies
BIO(4)							   BSD Kernel Interfaces Manual 						    BIO(4)

NAME
bio -- Block IO ioctl tunnel pseudo-device SYNOPSIS
pseudo-device bio DESCRIPTION
The bio driver provides userland applications ioctl(2) access to devices otherwise not found as /dev nodes. The /dev/bio device node oper- ates by delegating ioctl calls to a requested device driver. Only drivers which have registered with the bio device can be accessed via this interface. The following device drivers register with bio for volume management: arcmsr(4) Areca Technology Corporation SATA RAID controller cac(4) Compaq RAID array controller ciss(4) Compaq Smart ARRAY 5/6 SAS/SATA/SCSI RAID controller mfi(4) LSI Logic & Dell MegaRAID SAS RAID controller The following ioctl calls apply to the bio device: BIOCLOCATE Locate a named device and give back a cookie to the application for subsequent ioctl calls. The cookie is used to tunnel further ioctls to the right device. BIOCINQ Retrieve number of volumes and physical disks for a specific device. BIOCDISK Retrieve detailed information for the specified physical disk. Information returned can include status, size, channel, target, lun, vendor name, serial number, and processor device (ses). BIOCDISK_NOVOL Is just the same as BIOCDISK but doesn't require the disks to be in volume sets, so this applies to any physical disk con- nected to the controller. Note: this ioctl might not be supported on all hardware. BIOCVOL Retrieve detailed information for the specified volume. Information returned can include status, size, RAID level, number of disks, device name association (sd?) and vendor name. BIOCALARM Control the alarm beeper on the device. Supported states are: disable alarm, enable alarm, silence alarm, status and test alarm. Note: These options might not be supported on all hardware. BIOCBLINK Blink an LED of the specified physical disk. Supported blink states are: blink LED, unblink LED and blink alarm LED. Note: This option is only supported if the disk is governed by ses(4) and the hardware supports hardware blinking. BIOCSETSTATE Alter the state of specified physical disk. Supported states are: create/remove hot-spare, create/remove pass through disk, start/stop consistency check in a volume, online disk and offline disk. Note: These options might not be supported on all hardware. BIOCVOLOPS For operations in volume sets. It's able to create and remove a volume set in a supported RAID controller. Note: this ioctl might not be supported on all hardware. FILES
/dev/bio ioctl tunnel device SEE ALSO
ioctl(2), bioctl(8) HISTORY
The bio driver first appeared in OpenBSD 3.2 and NetBSD 4.0. AUTHORS
The bio driver was written by Niklas Hallqvist <niklas@openbsd.org>. The API was written by Marco Peereboom <marco@openbsd.org> and was extended even more for NetBSD by Juan Romero Pardines <xtraeme@netbsd.org>. BSD
May 25, 2008 BSD
All times are GMT -4. The time now is 07:09 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy