I configured en0 interface and I have a cable plugged into port 1 in the back of the server as there is only one nic installed with two interfaces and I have configured en0. Below is the output of the netstat -rn command.
it looks like when I ping the ip I set 10.52.44.250 it is replying through the loop back interface and not en0 why? Is there something else I need to configure to communicate on the network?
Thanks for the Help
Last edited by Scott; 03-03-2010 at 01:51 PM..
Reason: Code tags please...
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
LEARN ABOUT CENTOS
en
EN(4) BSD Kernel Interfaces Manual EN(4)NAME
en -- device driver for Midway-based ATM interfaces
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device en
device atm
device utopia
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_en_load="YES"
DESCRIPTION
The en device driver supports Midway-based ATM interfaces including the Efficient Networks, Inc. ENI-155 and Adaptec ANA-59x0. Midway is an
AAL5 SAR (Segmentation and Reassembly) chip.
For configuring the card for IP see natmip(4).
The following sysctls are recognized by the driver additionally to those handled by utopia(4):
hw.atm.enX.istats
Contains an array of uint32_t with internal driver statistics.
hw.atm.enX.debug
This is a bit map of debugging options. This variable is only available when the driver is compiled with debugging support.
The driver supports the media options sdh, noscramb and unassigned (see utopia(4)).
DIAGNOSTICS
en0 <Efficient Networks ENI-155p> rev 0 int a irq 5 on pci0:16
en0: ATM midway v0, board IDs 6.0, Utopia (pipelined), 512KB on-board RAM
en0: maximum DMA burst length = 64 bytes
en0: 7 32KB receive buffers, 8 32KB transmit buffers allocated
CAVEATS
The driver extensively uses DMA on PCI. The first generation PCI chipsets do not work or exhibit poor performance.
SEE ALSO natm(4), natmip(4), utopia(4), ifconfig(8), route(8)AUTHORS
Chuck Cranor of Washington University implemented en driver in 1996 for NetBSD.
BSD July 16, 2005 BSD