02-23-2010
check this
also found at
http://bizsupport.austin.hp.com/bc/d.../c00553302.pdf
page 19
Configuring the IP address
This step is necessary only if you are using a static IP address. When using dynamic IP addressing, your DHCP server will automatically assign an IP address for iLO 2. HP recommends using DNS or DHCP with iLO 2 to simplify installation
To configure a static IP address, use the iLO 2 RBSU with the following procedure to disable DNS and DHCP and configure the IP address and the subnet mask:
1. Restart or power up the server.
2. Press the F8 key when prompted during POST. The iLO 2 RBSU runs.
3. Select Network>DNS/DHCP, press the Enter key, and then select DHCP Enable. Press the spacebar to turn off DHCP. Be sure that DHCP Enable is set to Off, and save the changes.
4. Select Network>NIC>TCP/IP, press the Enter key, and enter the appropriate information in the IP Address, Subnet Mask, and Gateway IP Address fields.
5. Save the changes.
6. Exit iLO 2 RBSU. The changes take effect when you exit iLO 2 RBSU.
regards
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I have an application that requires me to disable the restricted access to the X Server libraries by issuing the 'Xhost +' command from a Console Window.
It is important that this command is run from the Console Window and not a Terminal Window otherwise the system complains that DISPLAY is not... (0 Replies)
Discussion started by: jimthompson
0 Replies
2. Solaris
Greetings All,
If someone/anyone reading this post has had success setting up and configuring HP iLO2 CLI virtual serial port for Solaris...please tell how.
I'm trying to get a remote console to an HP DL385 server via iLO2 and ssh. The server is running Solaris 10 (11/06), patched to... (1 Reply)
Discussion started by: alias.256
1 Replies
3. HP-UX
Hi,
I wanted to setup a ilo for an HP 9000 rp 8420 server. Can anyone have an idea on it? (1 Reply)
Discussion started by: gunnervarma
1 Replies
4. Linux
I have to write Linux script to findout what kind of ilo is been installed in the given ip address either ilo/LO100 or no device found.
IP address will be given in the command line of the script.
-> With out log on to the ip address, should get the ilo type installed in that machine.
1. I... (1 Reply)
Discussion started by: skmdu
1 Replies
5. Solaris
I have a brand new T5220 and I'm trying to configure the ILOM port with a static Ip address via the Serial Management port. I log on as "root" and then enter the commands ( see below) to config the port. When I enter the last command which is " set /SP/network commitpending=true", which I... (9 Replies)
Discussion started by: danfall4
9 Replies
6. Hardware
HI Guys
I have forgot my ILO password for REDHAT Linux, Its Protriat HP server.
I need to set new password for ILO without installing any RPM like "hponfig"....
I need to set password in terminal. please give me steps to change the password
waiting for ur replys (1 Reply)
Discussion started by: suresh_krish
1 Replies
7. IP Networking
Hi, I have two questions about HP system iLO:
(1) The <HP iLO 2 User Guide> says "Configure the IP address: This step is necessary only if you are using a static IP address. When using dynamic IP addressing, your DHCP server will automatically assign an IP address for iLO 2. HP recommends using... (6 Replies)
Discussion started by: aixlover
6 Replies
8. Shell Programming and Scripting
Hi,
I want to do momentary press to one server from linux is it possible? I got this command from internet is it correct? or need changes? I also need help how to start and reboot server in hp ilo from linux server.
fence_ilo -a 10.1.41.155 -l Admin -p Password (1 Reply)
Discussion started by: learnbash
1 Replies
9. UNIX for Dummies Questions & Answers
Hi,
I have Redhat Linux 5.9. I need to connect all the ILO to different switch which can support 1 Gig. How can I find if ILO port can support gigabit?
I am on HP website but not able to find anything about this information. Not sure I am looking in the correct place.
Please help. (3 Replies)
Discussion started by: samnyc
3 Replies
10. HP-UX
Fast question: a bad reset put ilo ip to 127.0.0.1(!)
and now i cannot reach via network
Is possible to get ilo via serial using COM1/console?
I see three console ports on server back side
two are standard and one is reachable only with this cable...
403 Forbidden
but i don't have this... (0 Replies)
Discussion started by: Linusolaradm1
0 Replies
LEARN ABOUT HPUX
pstatectl
pstatectl(1M) pstatectl(1M)
NAME
pstatectl - control processor performance states
SYNOPSIS
cpu] pstate| interval]
DESCRIPTION
The command is used to control processor performance states (P-states). On systems with supported processors and firmware, processor per-
formance states can reduce power consumption.
A supported processor implements a series of performance states, numbered from P0 to Pn, where n is implementation dependent. Each subse-
quent P-state consumes less power but offers less performance than the previous state.
provides access to both static and dynamic performance state usage modes. In static mode, the system remains in a specified P-state, where
power consumption and performance are reduced by a fixed amount. In dynamic mode, HP-UX will adjust the processors' P-states individually,
in response to the workload running on the system.
Enabling dynamic processor performance states will generally have a negligible effect on system performance, while at the same time reduc-
ing power consumption when the system is not fully loaded.
Options
recognizes the following options:
The operation will apply to the specified
processor only. If is not specified, the operation applies to the whole system.
The "status" operation will report detailed status for each processor.
Otherwise, a summary of the system state is reported.
Operands
recognizes the following operands; only one operand at a time can be specified on the command line:
Enable the dynamic P-states mode (processors will adjust performance to match the workload).
Disable the P-states (processors will always be at maximum performance).
Enable static mode (processors will always be in the specified P-state).
If the specified state is higher than is supported, the highest supported state is used instead. The state may be
specified as a number, or in P-state notation (for example, P0).
Enable dynamic P-states mode within the range of states specified.
and should be supplied as specified under the option.
Report information about the system's P-state capabilities,
the current P-state mode (static or dynamic), and whether HP-UX has control over processor P-states. If was speci-
fied, each processor's current P-state and operating mode are displayed.
Display a table listing the power consumption and relative performance of each P-state.
Print the number of the highest implemented P-state on the system.
If the system does not support P-states, the number is 0.
Change the time interval between dynamic mode state changes to the
specified duration. The minimum is 0.01 seconds, and the maximum is 600 seconds.
EXTERNAL INFLUENCES
On some systems, the Onboard Administrator may take control of P-states away from the operating system (for instance, when iLO is used to
place the system in Static High Performance or Static Low Power mode).
If HP-UX does not have control over processor performance states, the command will still work normally. However, any changes made to
P-state modes will have no effect until HP-UX regains control. The command will report whether HP-UX currently has control over P-states.
RETURN VALUE
returns the following values:
Successful completion.
Command failed.
DIAGNOSTICS
Make sure that the system has Itanium(R) 2 9100 series or later processors, and that the installed system firmware supports P-
states.
EXAMPLES
To enable dynamic P-states on the system:
To disable dynamic P-states on the system (all processors will be in maximum performance mode):
or
To restrict the system to P0 and P1 only:
DEPENDENCIES
Processor performance states require Itanium(R) 2 9100 series processors or later models. Some systems require a firmware update to use
processor performance states.
AUTHOR
was developed by HP.
SEE ALSO
(Itanium(R)-based Systems Only) pstatectl(1M)