02-18-2010
Okay, you even have an IP address so you seem to be able to talk to the router... How well we don't know yet.
It could potentially be an MTU problem. Try 'ifconfig wlan0 mtu 1364' and see if that helps.
If not, post the output of 'ping -c 4 192.168.1.1' so we can see how well your system can talk to the router. Then 'ping -c 4 66.82.4.8' to see if you can actually get through to the internet at all with it.
10 More Discussions You Might Find Interesting
1. IP Networking
How can I strengthen a 2.4 GHZ 802.11b wireless signal? (4 Replies)
Discussion started by: dangral
4 Replies
2. UNIX Desktop Questions & Answers
Hi guys, I've been a linux user for a day now and we are planning of moving from windows to gentoo.
unfortunately were having a heck of a trouble in configuring linksys wusb adaptor on our linux box. we got so tired of looking for any linux drivers or ndiswrapper blah for these critters but... (1 Reply)
Discussion started by: 3rr0r_3rr0r
1 Replies
3. Linux
got a wireless usb network card. how can i make it work under redhat9?. it does not come with linux driver. (0 Replies)
Discussion started by: GJ2
0 Replies
4. Solaris
Hi Community,
I'm working on Sun Server V490 with my PC (with OS Vista). I'm using a USB to Serial Adapter to connect to Server directly.
I've this problem, I'm connecting to Server with Putty client with this settings:
boud rate 9600, 8 bit, 0 parity, 0 flow control, but after to have typed... (4 Replies)
Discussion started by: Sunb3
4 Replies
5. Solaris
Hi,
i try to plug in my USB wireless adapter to my sun solaris server. However, it cannot detect it. How do i set it so that it can detect it? (1 Reply)
Discussion started by: lkyow
1 Replies
6. Red Hat
Hello all,
I am fed up on trying to install my newly purchased usb wireless antenna to my fedora14 machine; so I seek help of all you linux masterminds out there. It worked well in my Win XP. Please help me in setting up it to my Fedora. .
Details follows:
The device model is : Aztech... (5 Replies)
Discussion started by: gsabarinath
5 Replies
7. Hardware
How do I configure my wireless adapter to access the internet? I am running PCLinuxOS 2010. (0 Replies)
Discussion started by: ryan352333
0 Replies
8. Red Hat
hi everybody,
iam using 32 bit centos 6.2 on my machine. i have purchase TP-LINK, TL-WN727N wireless usb, but i was not able to install on my desktop. i was not able to find drivers for centos 6.2 official site of TPLINK.
$ uname -a
Linux workstation 2.6.32-220.el6.i686 #1 SMP Tue Dec 6... (0 Replies)
Discussion started by: paruhang
0 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD