02-12-2010
Replacing a tape drive on HP NetServer e800
This server had an HP C1555 tape drive that appears to have gone belly up. We found a replacement, an HP C1537, that we want to install. We did the hardware thing, with power off, of course, but when the box was rebooted it did not seem to recognize the drive. At least the backup software did not.
I'm a UNIX newbie, but an experienced MacOS and Windows geek. Can anyone please lay out the steps (from login) that are required to get the drive to work?
Any help will be greatly appreciated - this box runs proprietary software that we cannot access, and this software includes the backup of the built-in database. Needless to say, we are extremely vulnerable at this point....
Cheers,
8 More Discussions You Might Find Interesting
1. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
2. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
3. AIX
I've just landed in a situation where an old IBM RS/6000 7025 F40 running AIX 4.2.1 has had it's tape drive fail. The tape drive in question is an HP C1533A 4mm 4GB/8GB DAT drive. It repeatedly gets write failures, and my trusty techique of whacking the cleaning tape in hasn't worked. Unfortunately... (2 Replies)
Discussion started by: phaedrus
2 Replies
4. UNIX for Advanced & Expert Users
Hello sir
Please I just have tape blocked inside the tape drive of my server. My server have 2 tape drives configured but only one is available (rmt0). The problem is that i have a separed tape drive ready to be connected to my server and i wan to know how to make available the second tape drive ?... (0 Replies)
Discussion started by: sobnc
0 Replies
5. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
6. Solaris
Hey folks,
Linux admin here, forced to use Opensolaris to try to use ufsdump/ufsrestore to get some data of some old tapes.
I've got Opensolaris 2009.06 on x86 and a Sony SDX-700V.
As a "control" experiment, I booted the system with a Linux live CD and the tape drive worked perfectly.
... (2 Replies)
Discussion started by: eddy_sysad
2 Replies
7. UNIX for Dummies Questions & Answers
Hello everyone.
I googled a little bit, and the best anwers i had were found in this forum. But , unfortunately, they couldn't give me a solution. So i decided to ask the question completely.
I have two servers:
One RHEL 5 , x64 , with a SCSI DAT72 Tape Drive.
Another (the new one), with... (0 Replies)
Discussion started by: pablobhz
0 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
tms(7) Miscellaneous Information Manual tms(7)
NAME
tms - TMSCP magnetic tape interface
SYNOPSIS
For XMI/KDM on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
controller uq0 at xmi? port kdm vector uqintr
device tape tms0 at uq0 drive 0
For MSI Bus: only MIPS-based DECsystem 5500
bus msi0 at ibus? vector msi_isr
controller dssc1 at msi0 msinode 1
device tape tms3 at dssc1 drive 3
For XMI/CI/HSC on Alpha-based systems:
bus xmi0 at iop0 vector xmierror
bus ci0 at xmi? port np vector cimna_isr
controller hsc6 at ci0 cinode 6
device tape tms3 at hsc6 drive 3
For tms devices dual ported between two controllers:
device tape tms2 at * drive 2
DESCRIPTION
The TMSCP driver provides a standard tape drive interface, as described in mtio(7). This is a driver for any controller that adheres to
the Tape Mass Storage Control Protocol (TMSCP). The TMSCP controllers communicate with the host through a packet-oriented protocol termed
the Tape Mass Storage Control Protocol.
Tape Support - Alpha-based systems
TA78, TA79, TA81, TA90, TA90E, TA91
Diagnostics
All diagnostic messages are sent to the error logger subsystem.
FILES
/dev/rmt???
/dev/nrmt???
SEE ALSO
mtio(7), MAKEDEV(8), uerf(8), tapex(8) delim off
tms(7)