02-05-2010
From the HMC, we know the disks that are mapped to linux LPAR client, but we could not determine which specific linux client disk(sdb) corresponds to which specific disk/slot from the list of disks shown in HMC. Is there any way to find this from HMC or from VIO Server?
10 More Discussions You Might Find Interesting
1. AIX
Hi,
I define 2 new LV on the vio server and run a cfgmgr on the partition and see my 2 new hdisk (hdisk6 and hdisk7).
I extend my vg vg000 (on the partition) and add the 2 hdisks.
I had a filesystem on the vg000 and when I added the disk I would like to increase the filesystem. But I cannot do a... (0 Replies)
Discussion started by: touny
0 Replies
2. UNIX for Dummies Questions & Answers
Can you have a Dynamic LPAR without VIO and if yes is there a benefit to having both? I am attempting to implement VIO and Resource pooling at my company and want to understand the limitations.
Also, I have been told the managing and allocation of the Logical Volumes is a time consuming task as... (0 Replies)
Discussion started by: bombers73
0 Replies
3. AIX
We have a frame the uses 2 vios that assign disk storage to LPAR's. We have a LPAr with multiple disk and I want to know how do I tell which vio is serving the disk. For example the LPAr has hdisk 0, 1, 2, 3 all the same size. I want to know which vio is serving hdisk0, 1. (4 Replies)
Discussion started by: daveisme
4 Replies
4. AIX
hello Folks,
my vio:
$ lsmap -all
SVSA Physloc Client Partition ID
--------------- -------------------------------------------- ------------------
vhost0 U9117.MMA.6534BE4-V2-C11 0x00000003
VTD ... (0 Replies)
Discussion started by: filosophizer
0 Replies
5. AIX
Hi,
I was looking on Google for AIX-VIO/LPAR with ISCSI solution and found following really nice tutorial about how to setup ISCSI with free NAS.
1) Build Your Own Open Source NAS Device Using FreeNAS | Train Signal Training - Free Computer Training Videos
2) Build Your Own Open Source... (4 Replies)
Discussion started by: kabir
4 Replies
6. AIX
I am wondering if there is a command I can run from **with-in** LPAR server (server01) to find out the hostname or IP address or other parameters for VIO server in charge of server01? (1 Reply)
Discussion started by: ms1232
1 Replies
7. AIX
Just a question which may seem dumb to some out there, but then again I am not a super technie so that's my excuse.
Is it possible to say provision a test AIX LPAR (has a 10gb boot lun and 20gb data) under a VIO which has connectivity to SAN Array A so it can see the disks provisioned to it,... (2 Replies)
Discussion started by: Johnny1314
2 Replies
8. AIX
Hi All,
I've been trying to create a new LPAR for some days now but I can't get the VIO server to recognize the new LPAR. This is what I did:
On HMC create new LPAR
On HMC create new virtual scsi adapter for LPAR in VIO profile
On HMC add new virtual scsi adapter for LPAR with DLPAR... (6 Replies)
Discussion started by: petervg
6 Replies
9. AIX
:wall::wall::wall:
1. I have created an LPAR in the HMC.
2. I have allocated the storage from an Hitachi AMS2500 and assigned it to the host group.
3. I have zoned the LPAR and Storage on a Brocade 5100. (The zone sees the AMS)
Next I activated the LPAR in the HMC, SMS mode for the mksysb... (3 Replies)
Discussion started by: Dallasguy7
3 Replies
10. AIX
Hi Guys,
I have fresh new installed VIO 2.2.3.70 on a p710, 3 physical SAS disks, rootvg on hdisk0
and 3 VIO clients through vscsi, AIX7.1tl4 AIX6.1tl9 RHEL6.5ppc, each lpar has its rootvg installed on a LV on datavg (hdisk2) mapped to vhost0,1,2
There is no vg on hdisk1, I use it for my... (1 Reply)
Discussion started by: frenchy59
1 Replies
LEARN ABOUT DEBIAN
roar_vs_connection_obj
roar_vs_connection_obj(3) RoarAudio Programmer's Manual roar_vs_connection_obj(3)
NAME
roar_vs_connection_obj, roar_vs_stream_obj, roar_vs_vio_obj - VS API interface for use of main API
SYNOPSIS
#include <roaraudio.h>
struct roar_connection * roar_vs_connection_obj(roar_vs_t * vss, int * error);
struct roar_stream * roar_vs_stream_obj (roar_vs_t * vss, int * error);
struct roar_vio_calls * roar_vs_vio_obj (roar_vs_t * vss, int * error);
DESCRIPTION
Those functions return internal connection, stream and VIO object of the VS object. They are used to use the main API with a VS opened
stream.
roar_vs_connection_obj() returns the connection object used for the control connection to the server.
roar_vs_stream_obj() returns the stream object storing information about the stream.
roar_vs_vio_obj() returns the VIO object used to read data from or send data to the server.
Returned objects are freed as soon as the VS object is closed. If the VS object was created using roar_vs_new_from_con(3) the connection is
not closed by the VS object and stay valid after close until it is closed by the program or library.
The VIO object MUST NOT be used while in buffered mode.
PARAMETERS
vss The VS object to return internal objects from.
error This is a pointer to a integer used to store the error value in case of error. This can be NULL if not used but it is very recom-
mended to use this error value to report good error messages to the user.
RETURN VALUE
On success these calls return the described object. On error, NULL is returned.
EXAMPLES
FIXME
SEE ALSO
roarvs(7), libroar(7), RoarAudio(7).
RoarAudio May 2011 roar_vs_connection_obj(3)