Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Doubt with irq handler....... Post 302389154 by Corona688 on Friday 22nd of January 2010 11:42:12 PM
Old 01-23-2010
I suspect your test setup isn't actually producing interrupts. Try not loading your driver and running your trigger: dmesg should overflow with 'IRQ 10, nobody cared' messages.

Or, check 'cat /proc/interrupts' to see what it thinks is on those interrupts, they may be routed elsewhere internally. What kind of bus are you triggering on? If you're using ISA, make sure you assign those interrupts to ISA in the CMOS.

Last edited by Corona688; 01-23-2010 at 12:47 AM..
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

irq

where can i find the i/o and irq's in mandrake 8 help lost :D (2 Replies)
Discussion started by: RYRY46D9
2 Replies

2. UNIX for Dummies Questions & Answers

forcing irq on PCMCIA card

ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB. (supported according the PCMCIA docs) laptop is P-II lifetec /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 ( found via probe -m ) PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies

3. UNIX for Dummies Questions & Answers

usb - deleting (irq)

FreeBSD 4.5 i installed my sound drivers (which are onboard) with the following lines in my kernel device pcm options PNPBIOS then cd /dev sh MAKEDEV snd0 output from cat /dev/sndstat show the devicedriver (correct one) ok this works nice untill i enter my kde and want to play a... (1 Reply)
Discussion started by: termiEEE
1 Replies

4. UNIX for Dummies Questions & Answers

irq complication

hi, i looked around already and had no luck finding anything. Im trying ot install a wpc11v3 linksys wireless card, and i have been for about a week now. :mad: Im near certain i have figured out my problem. When i plug in my card while knoppix is running, it crashes. When i plug it into... (0 Replies)
Discussion started by: jestra
0 Replies

5. UNIX for Advanced & Expert Users

IRQ priority in FC9

Hi, I want to increase IRQ4 priority to maximum in Fedora core 9 (kernel version 2.6.25.11-97).If anybody knows plz help me.... I will be very thankful .. regards, Raj (0 Replies)
Discussion started by: rajuprade
0 Replies

6. SCO

IRQ conflict between USB and NIC SCO 5.0.7

I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port. After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded. As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies

7. Linux

A question with respect to IRQ distribution

Hi all, I am a Linux newbie in kernel development. In class I was asked a question about IRQ distribution as followed. IRQs can be distributed among the available CPUs (in a multiple-CPU system) in two ways: (1) Static distribution The IRQ signal is delivered to the local APICs listed... (2 Replies)
Discussion started by: sunnyhay
2 Replies

8. Programming

What is unbalanced IRQ?

------------------------ WARNING: at kernel/irq/manage.c:225 __enable_irq+0x3b/0x57() Unbalanced enable for IRQ 4 Modules linked in: svsknfdrvr Pid: 634, comm: ash Tainted: G W 2.6.28 #1 Call Trace: warn_slowpath+0x76/0x8d profile_tick+0x2d/0x57 irq_exit+0x32/0x34 ... (3 Replies)
Discussion started by: dragonpoint
3 Replies

9. Hardware

IRQ and Number of Devices

Hello everyone. I feel that I'm about to answer my own question, but I just want to be sure that I'm right. I know computers all use, at a very low level, the IRQ system of interrupting the CPU when it needs something. My questions are as follows: 1. Does the device in question, say.. a mouse,... (1 Reply)
Discussion started by: Lost in Cyberia
1 Replies

10. Programming

Serial port signal(IRQ) handler (using C)

Hello, I'm writing some serial(UART) handler but have stuck on few issues, maybe anyone can help to show me what I'm doing wrong. Basically I'm intending to write serial RX signal handler. Application receives defined packages of data over serial which contains header and payload. Handler... (3 Replies)
Discussion started by: Lauris_k
3 Replies
STRUCT 
UIO_INFO(9) Device drivers infrastructure STRUCT UIO_INFO(9) NAME
struct_uio_info - UIO device capabilities SYNOPSIS
struct uio_info { struct uio_device * uio_dev; const char * name; const char * version; struct uio_mem mem[MAX_UIO_MAPS]; struct uio_port port[MAX_UIO_PORT_REGIONS]; long irq; unsigned long irq_flags; void * priv; irqreturn_t (* handler) (int irq, struct uio_info *dev_info); int (* mmap) (struct uio_info *info, struct vm_area_struct *vma); int (* open) (struct uio_info *info, struct inode *inode); int (* release) (struct uio_info *info, struct inode *inode); int (* irqcontrol) (struct uio_info *info, s32 irq_on); }; MEMBERS
uio_dev the UIO device this info belongs to name device name version device driver version mem[MAX_UIO_MAPS] list of mappable memory regions, size==0 for end of list port[MAX_UIO_PORT_REGIONS] list of port regions, size==0 for end of list irq interrupt number or UIO_IRQ_CUSTOM irq_flags flags for request_irq priv optional private data handler the device's irq handler mmap mmap operation for this uio device open open operation for this uio device release release operation for this uio device irqcontrol disable/enable irqs when 0/1 is written to /dev/uioX COPYRIGHT
Kernel Hackers Manual 3.10 June 2014 STRUCT UIO_INFO(9)
All times are GMT -4. The time now is 08:49 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy