Sponsored Content
Operating Systems SCO SCO 5.0.7 no root disk controller found error during install Post 302389104 by FrictionBurn on Friday 22nd of January 2010 04:31:02 PM
Old 01-22-2010
Question SCO 5.0.7 no root disk controller found error during install

I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB drives on an HP 6400 smart array controller using smart start 7.1 and 1 logical drive configured on said array and a tape drive on the array controler as well. The onboard raid controllers have been disabled in the bios and nothing is attached to them. On bootup you can see the controlled being initialized and the drives in the array spinning up and it recognizes the logical drive.
I've tried using several variations on the defbootstr but still nothing seems to work so now i'm a bit stuck. Below is what I thought was the proper loader

defbootstr link=ciss hd=Sdsk Sdsk=ciss Srom=wd(0,0,0,0)

but alas, no luck so far. Does anyone have any suggestions?


Regards
 

10 More Discussions You Might Find Interesting

1. SCO

sco openserver 5.0.0 boot / root disk

Hi, I have an openserver 5.0.0 machine in the office. The sysad of that machine left years ago without leaving the password to anyone. I was wondering if someone has a copy of the boot / root diskettes (rescue) for this version? Or perhaps if anyone knows a download link / location in the... (0 Replies)
Discussion started by: marcpascual
0 Replies

2. SCO

Incorrect Disk Partition - New Install SCO 6.0

New IBM x3400 machine with a raid 5 configuration. Go through the early setup routine to the point where I answer the questions for time zone, machine name. Enter continue and get a message stating : "Incorrect disk partitioning cannot continue" This is a sco message, refers to the installation... (1 Reply)
Discussion started by: wjbtms
1 Replies

3. Solaris

Controller target disk?

Hi, I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below: /pci@8,600000/SUNW,qlc@2 LiD HA LUN --- Port WWN --- ----- Disk description ----- 0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies

4. SCO

warning:hd:no root disk controler was found

hi all i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow warning:hd:noroot disk controler was found hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies

5. SCO

Warning HD: no root disk controller was found

hi... i hav a problem to install sco unix while installing sco unix 5.0.5 in acer altos with hardware raid am getting error "Warning HD: no root disk controller was found system error 5: while getting fs type flushing controller: DAC960PRL cache done." i hav use the following... (18 Replies)
Discussion started by: mselvaprakash
18 Replies

6. SCO

Change Disk controller in SCO 6.0.0

So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller. First, I downloaded the megasas driver from SCO and installed it on the old system. Then I created a new Microlite Edge emergency boot cd with the new driver on it. I... (2 Replies)
Discussion started by: jgt
2 Replies

7. SCO

Getting error sco unix 507 from cdrom:no controller for device you chosen

Installing SCO UNIX 507 on Dell Poweredge T610. It has no floppy so I downloaded the BTLD onto CD from SCO site to load without floppy drive. BTLD loads ok. when i get to the Media to be used, no matter what option i chose i get the error: No controller for device you have chosen. During bootup you... (9 Replies)
Discussion started by: romanglad112
9 Replies

8. SCO

SCO Openserver 5 root password and disk full

Hi, We have an old SCO Openserver 5.0.7 server that I have inherited that currently has two issues that we are trying to resolve. 1. We do not know the root password. I have contacted the old admin, looked for rescue disk and documentation but there appears to be nothing. I have tried... (1 Reply)
Discussion started by: acerimmer10
1 Replies

9. Solaris

Disk controller reassignment

Hi The scenario in the oracle t4-1 hardware with solaris 10 is as follows: 1. The initial install on the server was performed with an incorrect disk layout. 2. New disks were ordered and slot into the server. 3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies

10. SCO

SCO unresponsive after root disk

I am working on a system that uses SCO Unix 5. I started later in this troubleshooting process so I have had to play catch up on some of the earlier mistakes that were made. The HD was formatted using the SCSI controller cards bios. I have 2 recovery floppies the boot and the root. After... (19 Replies)
Discussion started by: graysona
19 Replies
MLXCTL(8)						    BSD System Manager's Manual 						 MLXCTL(8)

NAME
mlxctl -- Mylex DAC960 family management utility SYNOPSIS
mlxctl [-f dev] [-v] [-a] status [drive] [...] mlxctl [-f dev] [-a] detach [drive] [...] mlxctl [-f dev] [-a] check [drive] [...] mlxctl [-f dev] rebuild channel:target mlxctl [-f dev] cstatus mlxctl [-f dev] rescan mlxctl [-f dev] config DESCRIPTION
The mlxctl utility performs status monitoring and management functions for Mylex DAC960 RAID controllers and attached devices. The following options are available: -a Apply the action to all drives attached to the controller. -f dev Specify the control device to use. The default is /dev/mlx0. -v Increased verbosity. The following commands are available: cstatus Display the controller's current status. status Display the status of the specified drives. This command returns 0 if all drives tested are online, 1 if one or more drives are critical and 2 if one or more are offline. rescan Re-scan the logical drive table, and attach or detach devices from the system as necessary. detach Detach the specified drives. Drives must be unmounted and unopened for this command to succeed. check Initiate a consistency check and repair pass on a drive that provides redundancy (e.g., RAID1 or RAID5). This command returns imme- diately. The status command can be used to monitor the progress of the check. rebuild Rebuild onto the specified physical drive. Note that there can be only one running rebuild operation per controller at any given time. This command returns immediately. The cstatus command can be used to monitor the progress of the rebuild. config Write the current system drive configuration to stdout. EXAMPLES
Display the status of drive ld3 attached to the controller mlx1: mlxctl -f /dev/mlx1 -v status ld3 SEE ALSO
ld(4), mlx(4) HISTORY
The mlxctl command first appeared in NetBSD 1.5.3, and was based on the mlxcontrol utility found in FreeBSD. BUGS
Modifying drive configuration is not yet supported. Some commands do not work with older firmware revisions. Error log extraction is not yet supported. BSD
April 10, 2000 BSD
All times are GMT -4. The time now is 02:00 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy