Sponsored Content
Top Forums UNIX for Dummies Questions & Answers Doubt with irq handler....... Post 302389091 by Corona688 on Friday 22nd of January 2010 03:03:21 PM
Old 01-22-2010
I meant the computer.
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

irq

where can i find the i/o and irq's in mandrake 8 help lost :D (2 Replies)
Discussion started by: RYRY46D9
2 Replies

2. UNIX for Dummies Questions & Answers

forcing irq on PCMCIA card

ENV: linux Version: Mandrake 8.1, PCMCIA card: longshine lcs-8534TB. (supported according the PCMCIA docs) laptop is P-II lifetec /etc/sysconfig/pcmcia: PCMCIA=yes PCIC=i82365 ( found via probe -m ) PCIC_OPTS="cs_irq=11 pci_irq_list=11,11 do_scan=0" ( you see i want to force irq 11 )... (3 Replies)
Discussion started by: progressdll
3 Replies

3. UNIX for Dummies Questions & Answers

usb - deleting (irq)

FreeBSD 4.5 i installed my sound drivers (which are onboard) with the following lines in my kernel device pcm options PNPBIOS then cd /dev sh MAKEDEV snd0 output from cat /dev/sndstat show the devicedriver (correct one) ok this works nice untill i enter my kde and want to play a... (1 Reply)
Discussion started by: termiEEE
1 Replies

4. UNIX for Dummies Questions & Answers

irq complication

hi, i looked around already and had no luck finding anything. Im trying ot install a wpc11v3 linksys wireless card, and i have been for about a week now. :mad: Im near certain i have figured out my problem. When i plug in my card while knoppix is running, it crashes. When i plug it into... (0 Replies)
Discussion started by: jestra
0 Replies

5. UNIX for Advanced & Expert Users

IRQ priority in FC9

Hi, I want to increase IRQ4 priority to maximum in Fedora core 9 (kernel version 2.6.25.11-97).If anybody knows plz help me.... I will be very thankful .. regards, Raj (0 Replies)
Discussion started by: rajuprade
0 Replies

6. SCO

IRQ conflict between USB and NIC SCO 5.0.7

I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port. After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded. As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies

7. Linux

A question with respect to IRQ distribution

Hi all, I am a Linux newbie in kernel development. In class I was asked a question about IRQ distribution as followed. IRQs can be distributed among the available CPUs (in a multiple-CPU system) in two ways: (1) Static distribution The IRQ signal is delivered to the local APICs listed... (2 Replies)
Discussion started by: sunnyhay
2 Replies

8. Programming

What is unbalanced IRQ?

------------------------ WARNING: at kernel/irq/manage.c:225 __enable_irq+0x3b/0x57() Unbalanced enable for IRQ 4 Modules linked in: svsknfdrvr Pid: 634, comm: ash Tainted: G W 2.6.28 #1 Call Trace: warn_slowpath+0x76/0x8d profile_tick+0x2d/0x57 irq_exit+0x32/0x34 ... (3 Replies)
Discussion started by: dragonpoint
3 Replies

9. Hardware

IRQ and Number of Devices

Hello everyone. I feel that I'm about to answer my own question, but I just want to be sure that I'm right. I know computers all use, at a very low level, the IRQ system of interrupting the CPU when it needs something. My questions are as follows: 1. Does the device in question, say.. a mouse,... (1 Reply)
Discussion started by: Lost in Cyberia
1 Replies

10. Programming

Serial port signal(IRQ) handler (using C)

Hello, I'm writing some serial(UART) handler but have stuck on few issues, maybe anyone can help to show me what I'm doing wrong. Basically I'm intending to write serial RX signal handler. Application receives defined packages of data over serial which contains header and payload. Handler... (3 Replies)
Discussion started by: Lauris_k
3 Replies
STRUCT 
IRQ_CHIP(9) Structures STRUCT IRQ_CHIP(9) NAME
struct_irq_chip - hardware interrupt chip descriptor SYNOPSIS
struct irq_chip { const char * name; unsigned int (* startup) (unsigned int irq); void (* shutdown) (unsigned int irq); void (* enable) (unsigned int irq); void (* disable) (unsigned int irq); void (* ack) (unsigned int irq); void (* mask) (unsigned int irq); void (* mask_ack) (unsigned int irq); void (* unmask) (unsigned int irq); void (* eoi) (unsigned int irq); void (* end) (unsigned int irq); int (* set_affinity) (unsigned int irq,const struct cpumask *dest); int (* retrigger) (unsigned int irq); int (* set_type) (unsigned int irq, unsigned int flow_type); int (* set_wake) (unsigned int irq, unsigned int on); void (* bus_lock) (unsigned int irq); void (* bus_sync_unlock) (unsigned int irq); #ifdef CONFIG_IRQ_RELEASE_METHOD void (* release) (unsigned int irq, void *dev_id); #endif const char * typename; }; MEMBERS
name name for /proc/interrupts startup start up the interrupt (defaults to ->enable if NULL) shutdown shut down the interrupt (defaults to ->disable if NULL) enable enable the interrupt (defaults to chip->unmask if NULL) disable disable the interrupt ack start of a new interrupt mask mask an interrupt source mask_ack ack and mask an interrupt source unmask unmask an interrupt source eoi end of interrupt - chip level end end of interrupt - flow level set_affinity set the CPU affinity on SMP machines retrigger resend an IRQ to the CPU set_type set the flow type (IRQ_TYPE_LEVEL/etc.) of an IRQ set_wake enable/disable power-management wake-on of an IRQ bus_lock function to lock access to slow bus (i2c) chips bus_sync_unlock function to sync and unlock slow bus (i2c) chips release release function solely used by UML typename obsoleted by name, kept as migration helper AUTHORS
Thomas Gleixner <tglx@linutronix.de> Author. Ingo Molnar <mingo@elte.hu> Author. COPYRIGHT
Kernel Hackers Manual 2.6. July 2010 STRUCT IRQ_CHIP(9)
All times are GMT -4. The time now is 06:42 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy