11-13-2009
I wanted to know how impl. in C
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. Programming
Hello
I have a problem with retreiving network interface list using IOCTLs. I have 4 interfaces:
$ ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope... (1 Reply)
Discussion started by: xyzt
1 Replies
3. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
4. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
5. Linux
Hi,
Can any one please help me increase the arp stale time of an ipv6 interface on linux platform ?
I have tried increasing the variable gc_stale_time but that doesnt work.
Thanks (2 Replies)
Discussion started by: dkothapa
2 Replies
6. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
7. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
8. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
9. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
10. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
LEARN ABOUT LINUX
platform
platform(n) Tcl Bundled Packages platform(n)
__________________________________________________________________________________________________________________________________________________
NAME
platform - System identification support code and utilities
SYNOPSIS
package require platform ?1.0.4?
platform::generic
platform::identify
platform::patterns identifier
_________________________________________________________________
DESCRIPTION
The platform package provides several utility commands useful for the identification of the architecture of a machine running Tcl.
Whilst Tcl provides the tcl_platform array for identifying the current architecture (in particular, the platform and machine elements) this
is not always sufficient. This is because (on Unix machines) tcl_platform reflects the values returned by the uname command and these are
not standardized across platforms and architectures. In addition, on at least one platform (AIX) the tcl_platform(machine) contains the CPU
serial number.
Consequently, individual applications need to manipulate the values in tcl_platform (along with the output of system specific utilities) -
which is both inconvenient for developers, and introduces the potential for inconsistencies in identifying architectures and in naming con-
ventions.
The platform package prevents such fragmentation - i.e., it establishes a standard naming convention for architectures running Tcl and
makes it more convenient for developers to identify the current architecture a Tcl program is running on.
COMMANDS
platform::identify
This command returns an identifier describing the platform the Tcl core is running on. The returned identifier has the general for-
mat OS-CPU. The OS part of the identifier may contain details like kernel version, libc version, etc., and this information may con-
tain dashes as well. The CPU part will not contain dashes, making the preceding dash the last dash in the result.
platform::generic
This command returns a simplified identifier describing the platform the Tcl core is running on. In contrast to platform::identify
it leaves out details like kernel version, libc version, etc. The returned identifier has the general format OS-CPU.
platform::patterns identifier
This command takes an identifier as returned by platform::identify and returns a list of identifiers describing compatible architec-
tures.
KEYWORDS
operating system, cpu architecture, platform, architecture
platform 1.0.4 platform(n)