|
|
Sponsored Content
|
|
10 More Discussions You Might Find Interesting
1. AIX
I try to migrate a NIM server from one server to another.
I try to do a mksysb on NIM server
restore the NIM server's mksysb to a client through NIM installation
shutdown NIM server
start newly installed client as NIM server
Does anyone do this before? who can give me some suggestion? (1 Reply)
Discussion started by: yanzhang
1 Replies
2. AIX
Hello all,
I have a NIM master already up and running. When I try to add a client to the NIM environment (from client side), I get the following errors:
1) 0042-376 niminit: This command cannot be executed on a NIM master unless the "is_alternate" attribute is specified.
(I never... (5 Replies)
Discussion started by: solaix14
5 Replies
3. AIX
Hello guys,
what is a sure-shot single command to find out if the NIM environment is working properly from both master as well as client side? (2 Replies)
Discussion started by: solaix14
2 Replies
4. AIX
I have been trying to increase the NIM usage in my AIX environment especially for patching, got few questions
1. If I have a service pack available in the nim server, how do I define that particular directory as an LPP source, without again copying it somewhere else ie I want to define that... (5 Replies)
Discussion started by: balaji_prk
5 Replies
5. AIX
Hello everyone
I have two questions.
1.-The NIM and EZNIM are the same.
2.-If I have in one partition NIM installed I need to install EZNIM or I need to unistall NIM and then install EZNIM.
Thanks for your comments. (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
6. AIX
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
7. AIX
Hello
I would like to hear your opinions about shell and nimsh
I install the nim master on a server and and client nim on others servers. I backup this clients with the NIM master.
When Im trying to install the clients with the option nimsh (communication protocol) send me an error
... (1 Reply)
Discussion started by: lo-lp-kl
1 Replies
8. AIX
Hi.
I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ?
Tks (2 Replies)
Discussion started by: stephnane
2 Replies
9. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
10. AIX
Friend's,
I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client?
All leads to the answer would be much appreciated, many thanks!
-- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies
LEARN ABOUT CENTOS
nisd_resolv
rpc.nisd_resolv(1M) System Administration Commands rpc.nisd_resolv(1M) NAME
rpc.nisd_resolv, nisd_resolv - NIS+ service daemon SYNOPSIS
rpc.nisd_resolv [-v | -V] [ -F [-C fd]] [-t xx] [-p yy] DESCRIPTION
rpc.nisd_resolv is an auxiliary process which provides DNS forwarding service for NIS hosts requests to both ypserv and rpc.nisd that are running in the NIS compatibility mode. It is generally started by invoking rpc.nisd(1M) with the -B option or ypserv(1M) with the -d option. Although it is not recommended, rpc.nisd_resolv can also be started independently with the following options. This command requires that the /etc/resolv.conf file be setup for communication with a DNS nameserver. The nslookup utility can be used to verify communication with a DNS nameserver. See resolv.conf(4) and nslookup(1M). OPTIONS
-F Run in foreground. -C fd Use fd for service xprt (from nisd). -v Verbose. Send output to the syslog daemon. -V Verbose. Send output to stdout. -t xx Use transport xx. -p yy Use transient program# yy. ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWnisu | +-----------------------------+-----------------------------+ SEE ALSO
nslookup(1M), rpc.nisd(1M), resolv.conf(4), attributes(5) NOTES
NIS+ might not be supported in future releases of the SolarisTM Operating Environment. Tools to aid the migration from NIS+ to LDAP are available in the Solaris 9 operating environment. For more information, visit http://www.sun.com/directory/nisplus/transition.html. SunOS 5.10 12 Dec 2001 rpc.nisd_resolv(1M)