10-15-2009
the last time i've seen this problem the mainboard had been changed... but before order new hardware try a complete powercylce. pull the power cords and wait for 3-5 minutes and after that power the server on again. after that run again the firmware and bios update.
Last edited by DukeNuke2; 10-16-2009 at 05:28 AM..
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I need to totally power down my UNIX box, I think the script is
shutdown -y -i5 -g0
I know -i6 is for a clean reboot but I can't remember if -i5 is the power down script.....
Can anyone tell me if this is correct.
Thanks
:confused: (5 Replies)
Discussion started by: dman110168
5 Replies
2. Solaris
Problem powering ON the SUN 450 E, we checked voltage and the power supply. Seems to be we have out of 3 LED's in the back 2 are glowing, when we turn the power button on the front from standby to ON.
Does anyone know how to troubleshoot this?.
I have looked through some troubleshooting... (2 Replies)
Discussion started by: calsum
2 Replies
3. Shell Programming and Scripting
Hi there
I am running a script on a central box (boxA) that will send a remote request to boxB to perform a ping test to an ip
note: I am not pinging boxB from boxA but sending a request over ssh to get boxB to perform a ping test !
The thing is, I want the script back at boxA to know... (4 Replies)
Discussion started by: hcclnoodles
4 Replies
4. Solaris
my system has 128G of installed memory. top, vmstat shows the system has just over 10G of free memory on the system. but as per prstat o/p the usage is just 50-55G is there anyway i can find which process/zone is using more memory ?
System has 3 zones and all running application servers.
... (1 Reply)
Discussion started by: fugitive
1 Replies
5. Solaris
I have a T5240 server with following swap configuration
$ grep tmp /etc/vfstab
swap - /tmp tmpfs - yes -
$ swap -l
swapfile dev swaplo blocks free
/dev/swap 4294967295,4294967295 16 213909472 213909472
... (4 Replies)
Discussion started by: fugitive
4 Replies
6. Solaris
Hi, I wanted to configure a mail system on my UNIX box.
For that I read a document Sun Internet Mail Server 3.5 Advanced Installation Guide: Contents which is actually quite useful document but I am not sure from where can I bring patch? Is this patch will come in any CD form which I need to run... (1 Reply)
Discussion started by: Dhruvak
1 Replies
7. Solaris
am trying to install Solaris 10 32-bit on a VM Virtual Box Machine. When I get past GRUB and the program goes to install I get the following error:
panic/thread=fec20720: page fe2a1eb0 is not locked
The virtual machine is running off Windows 7 64-bit, if this helps. How do I get past this... (1 Reply)
Discussion started by: jastanle84
1 Replies
8. Solaris
One of our system is running 3 oracle db instances. And as per prstat o/p the system is approximately using 78G of swap memory
# prstat -J -n 2,15
PROJID NPROC SWAP RSS MEMORY TIME CPU PROJECT
4038 557 31G 29G 22% 113:23:43 10% proj1
4036 466 20G 19G... (2 Replies)
Discussion started by: fugitive
2 Replies
9. AIX
Hi,
monitor memory usage on AIX machine on any day of the week from 3:00 PM ET to 5:00 PM ET -
Povide min and max memory consumption.
Determine if all of the available memory is visible to the operating system. If it is not, determine the amount of memory which may be allocated to the... (3 Replies)
Discussion started by: Rookie_newbie
3 Replies
10. Solaris
I switched on the power to the server. But, the server did not power on i.e., none of the 3 LEDs on the front panel is lighted.
(Power supplies are showing only amber LEDs with "Ready to remove" sign).
I tried to turn on the power supplies via System Controller menu (platform shell), but it... (6 Replies)
Discussion started by: solind
6 Replies
APM(1) APM(1)
NAME
apm - interface with the APM subsystem
SYNOPSIS
apm [ -VvmMsSdin ]
DESCRIPTION
This command requires the Advanced Power Management subsystem. If run without arguments it reads /proc/apm and presents the output in a
human-readable format.
Given a -S or -s option it requests that the machine be put into the APM standby or the APM suspend state, respectively. For a brief
description of these states, see apmd(8).
OPTIONS
-V, --version
Print the version of the program and exit.
-v, --verbose
Also print version information for the APM subsystem. The APM subsystem consists of power-management hardware, firmware usually
referred to as the APM BIOS and a driver in the operating system kernel.
-m, --minutes
Print the time remaining as a number of minutes. The default is to print the time remaining in "hours:minutes" format.
-M, --monitor
Continuously monitor and update the status information. Assumes that the standard output is a terminal.
-S, --standby
Request that the machine be put into the APM standby state.
-s, --suspend
Request that the machine be put into the APM suspend state.
-d, --debug
Print APM status information in a format more useful for debugging. Implies -v.
FILES
/proc/apm
AUTHOR
This program was written by Rik Faith (faith@cs.unc.edu) and may be freely distributed under the terms of the GNU General Public License.
There is ABSOLUTELY NO WARRANTY for this program. The current maintainer is Avery Pennarun (apenwarr@worldvisions.ca).
SEE ALSO
xapm(1), apmd(8).
January 2004 APM(1)