Network interface goes down intermittently Post: 302360378

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt

2. Gentoo

Turning on/off the network interface

Hi all, I'm trying to write a script that will turn off the network interface eth0 on a linux Gentoo machine and then turn it back on, any help? Thanks, Neked

3. Solaris

Hi All, I want to configure network into my system. i tried following in to configure the interface to find the name of interface #prtdiag |grep net i got following 0 PCI-1 33 1 network-SUNW, hme then i tried following #prtconf -v |grep net network, instance #0

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that.

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help.

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a...

9. Solaris

Rename network interface

Hi all, I'm new here and looking for some help. I'm looking for the way to rename the network interfaces for Solaris 10. Got a server with 2 network cards (say "igb0" and "igb1") and there were some reasons that I have to swap the pci slots for those cards. However, after I did that, Solaris 10...

10. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without...

LEARN ABOUT OSF1

rcinet

rcinet(8)						      System Manager's Manual							 rcinet(8)

NAME

       rcinet - Restarts, starts, or stops Internet network services on the system

SYNOPSIS

       /usr/sbin/rcinet option

OPTIONS

       You  must specify one of the following options with the rcinet command: Restarts the network on the system.  Starts the network on the sys-
       tem.  Stops the network on the system.

       You can restrict the restart, start, or stop operation to either IPv4 or IPv6 networks by specifying inet or inet6,  respectively,  as  the
       second parameter.  By default, the script assumes both IPv4 and IPv6.

DESCRIPTION

       The  rcinet  script allows system administrators to restart, start, or stop the Internet network services on the system while it is running
       in multiuser mode by using one of the options.

RESTRICTIONS

       Superuser privilege is required.

       Warn users that the system is being removed from the network.

       File systems that were not mounted using the /etc/fstab file or the automount command must be unmounted with the umount command.  You  must
       remount these file systems using the mount command after the network is started on your system.

ERRORS

       The rcinet script prints an error message to stderr if the network is not configured on the system.

FILES

       The network shell scripts are located in /sbin/init.d with symbolic links in /sbin/rc0.d and /sbin/rc3.d.

SEE ALSO

       Commands: mount(8)

       Network Administration

																	 rcinet(8)

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Discussion started by: witt

2. Gentoo

Turning on/off the network interface

Discussion started by: neked

3. Solaris

Network interface issue

Discussion started by: kumarmani