10-07-2009
i hav already changed the scsi hard disk, hardware raid card, ram, scsi cd drive.. but it's still not working.........
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
LEARN ABOUT NETBSD
cmdide
CMDIDE(4) BSD Kernel Interfaces Manual CMDIDE(4)
NAME
cmdide -- CMD Technology and Silicon Image IDE disk controllers driver
SYNOPSIS
cmdide* at pci? dev ? function ? flags 0x0000
options PCIIDE_CMD064x_DISABLE
options PCIIDE_CMD0646U_ENABLEUDMA
DESCRIPTION
The cmdide driver supports the CMD Technology PCI0640, PCI0643, PCI0646, PCI0648, PCI0649, and Silicon Image 0680 IDE controllers, and pro-
vides the interface with the hardware for the ata(4) driver.
The 0x0002 flag forces the cmdide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO
ata(4), atapi(4), intro(4), pci(4), pciide(4), wd(4), wdc(4)
BUGS
There's no way to reliably know if a PCI064x controller is enabled or not. If the driver finds a PCI064x, it will assume it is enabled
unless the PCIIDE_CMD064x_DISABLE option is specified in the kernel config file. This will be a problem only if the controller has been dis-
abled in the BIOS and another controller has been installed and uses the ISA legacy I/O ports and interrupts.
The PCI0646U controller is known to be buggy with Ultra-DMA transfers, so Ultra-DMA is disabled by default for this controller. To enable
Ultra-DMA, use the PCIIDE_CMD0646U_ENABLEUDMA option. Ultra-DMA can eventually be disabled on a per-drive basis with config flags, see
wd(4).
The timings used for the PIO and DMA modes for controllers listed above are for a PCI bus running at 30 or 33 MHz. This driver may not work
properly on overclocked systems.
BSD
December 13, 2003 BSD