|
|
Sponsored Content
Special Forums
IP Networking
Maximum IP Address Configured on Intel Network Adapter
Post 302359587 by wilsonSurya on Wednesday 7th of October 2009 03:18:55 AM
10-07-2009
Maximum IP Address Configured on Intel Network Adapter
|
|
10 More Discussions You Might Find Interesting
1. Solaris
Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so? (1 Reply)
Discussion started by: ghuber
1 Replies
2. AIX
I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not... (1 Reply)
Discussion started by: johnf
1 Replies
3. AIX
hello
i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 )
what i need to do after the new adapter installed on the machine?
thanks
best regards
ariec (1 Reply)
Discussion started by: ariec
1 Replies
4. AIX
When I configure two VIO Servers, VIOS1 used to ping its gateway, after I configured second VIOS2, VIOS1 cannpt ping its gateway, when I run this command:
entstat -all ent#|grep -i priority
Priority: 5 Active: False
How to make Active to True? (1 Reply)
Discussion started by: rainbow_bean
1 Replies
5. UNIX for Dummies Questions & Answers
Hi All,
I am new here - this is my first post.
I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the... (1 Reply)
Discussion started by: soulmerchant
1 Replies
6. UNIX for Dummies Questions & Answers
Hi All
I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached.
I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network... (8 Replies)
Discussion started by: flashinwrx
8 Replies
7. UNIX for Dummies Questions & Answers
Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean?
- It has to run on all network adapters
- It has to be as simple as it can be
- It has to run on all linux distributions (or at least most of them)
- It does not have to run a network... (4 Replies)
Discussion started by: Chrisdot
4 Replies
8. IP Networking
Hi,
I just want to know whether two MAC address can exist in a adapter..
I mean one there will be mandatory one
And another as user defined one..
Any replies will be more helpful..
Please help..
:wall: (0 Replies)
Discussion started by: Priya Amaresh
0 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies