Configure Sun Cluster Post: 302356934

9 More Discussions You Might Find Interesting

1. High Performance Computing

SUN Cluster Vs Veritas Cluster

Dear All, Can anyone explain about Pros and Cons of SUN and Veritas Cluster ? Any comparison chart is highly appreciated. Regards, RAA

2. Solaris

How to configure zones into Single node cluster

Hi Gurus, For learning purpose, I have installed a single node cluster 3.2 on Solaris 10 for practice. Now I am welling to create two non-global zone and create them as a fail over. Will appreciate your help and assistance. Thanks

3. Solaris

sun cluster

hi can u please send me how to configure cluster in x86 machines. i am using VM ware. Is there any difference in X86 and SPARC cluster installations please help me thaks to all

4. Solaris

Sun Cluster 3.2

Hi, I am getting these messages constantly at random times there is not visible impact but would like to know what these messages mean? Cluster.RGM.rgmd: resource group on node change to RG_ON_PENDING_R_RERT Cluster.RGM.rgmd: resource group on node change to RG_ONLINE

5. Solaris

Sun cluster and Veritas cluster question.

Yesterday my customer told me to expect a vcs upgrade to happen in the future. He also plans to stop using HDS and move to EMC. Am thinking how to migrate to sun cluster setup instead. My plan as follows leave the existing vcs intact as a fallback plan. Then install and build suncluster on...

6. Solaris

Sun cluster 3.2

Hi I have a new mount point which is to added to to an existing resource group. I read many docs but I am not able to find the exact methods. Could anyone help me pls.

7. Solaris

Sun cluster 4.0 - zone cluster failover doubt

Hello experts - I am planning to install a Sun cluster 4.0 zone cluster fail-over. few basic doubts. (1) Where should i install the cluster s/w binaries ?. ( global zone or the container zone where i am planning to install the zone fail-over) (2) Or should i perform the installation on...

8. Red Hat

How can i configure fence_cisco_ucs with redhat cluster suite

HI How can i configure fence_cisco_ucs with redhat cluster suite. i was trying to configure fencing aganet with red ahat cluster suite i issued command # /usr/sbin/fence_vmware_soap -a 172.22.90.61 -l admin -p duc2Cisco -o reboot then i got below error: Failed: You have to...

9. Solaris

Sun cluster v3.2 - Is this right?

Running Sun Cluster v3.2 it appears. Two clustered physcial servers both running Solaris 10. Both servers run a number of Oracle DBs etc. BUT I'm a bit concerned that its been set up but will never switch in the even of failure of one of the hosts? Some of the cluster groups we've...

LEARN ABOUT OPENSOLARIS

scshutdown

scshutdown(1M)						  System Administration Commands					    scshutdown(1M)

NAME

       scshutdown - shut down a cluster

SYNOPSIS

       scshutdown [-y] [-g grace-period] [message]

DESCRIPTION

       Note -

	 Beginning  with  the Sun Cluster 3.2 release, Sun Cluster software includes an object-oriented command set. Although Sun Cluster software
	 still supports the original command set, Sun Cluster procedural documentation uses only the object-oriented command set. For more  infor-
	 mation about the object-oriented command set, see the Intro(1CL) man page.

       The scshutdown utility shuts down an entire cluster in an orderly fashion.

       Before starting the shutdown, scshutdown sends a warning message, then a final message asking for confirmation.

       Only run the scshutdown command from one node.

       The scshutdown command performs the following actions when it shuts down a cluster:

	   o	  Changes  all	functioning  resource groups on the cluster to an offline state. If any transitions fail, scshutdown does not com-
		  plete and displays an error message.

	   o	  Unmounts all cluster file systems. If any unmounts fail, scshutdown does not complete and displays an error message.

	   o	  Shuts down all active device services. If any transition of a device fails, scshutdown does not complete and displays  an  error
		  message.

	   o	  Runs /usr/sbin/init 0 on all nodes. See init(1M) for more information.

       You can use this command only in the global zone.

       You need solaris.cluster.system.admin RBAC authorization to use this command. See rbac(5).

OPTIONS

       The following options are supported:

       -g grace-period	   Changes the number of seconds from the 60-second default to the time specified by grace-period.

       -y		   Pre-answers the confirmation question so the command can be run without user intervention.

OPERANDS

       The following operands are supported:

       message		   Is a string that is issued after the standard warning message The system will be shut down in ... is issued. If message
			   contains more than one word, delimit it with single (') or double (") quotation marks.  The	warning  message  and  the
			   user-provided  message  are	output	when there are 7200, 3600, 1800, 1200, 600, 300, 120, 60, and 30 seconds remaining
			   before scshutdown begins.

EXAMPLES

       Example 1 Shutting Down a Cluster

	 phys-palindrome-1# scshutdown

EXIT STATUS

       The following exit values are returned:

       0		   The command completed successfully.

       nonzero		   An error occurred. Error messages are displayed on the standard output.

ATTRIBUTES

       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWsczu			   |
       +-----------------------------+-----------------------------+
       |Interface Stability	     |Evolving			   |
       +-----------------------------+-----------------------------+

SEE ALSO

       Intro(1CL), cluster(1CL), shutdown(1M), init(1M), attributes(5)

Sun Cluster 3.2 						    10 Apr 2006 						    scshutdown(1M)