09-24-2009
there are three disk they are
" Segate cheetah Model no: ST318406LC ultra3 SCSI 10k 18GB "
three disk are same disk
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
2. SCO
hi all
i use sco open server reliseas 5 on my system i get an image from system hard disk to another hard disk with acronis software and start system with new(backup)hard disk, but during the boot process some errors generate as follow
warning:hd:noroot disk controler was found
hd:a boot-time... (2 Replies)
Discussion started by: mehran_malek
2 Replies
3. HP-UX
Replace an unknown status controller on HP FC60 disk array
Author:JoyOnline JoyChangLu@gmail.com
Trouble description:
The users detected that the status of controller at A is unknown.
Analysis and diagnostic:
Physical observed all leds on enclosure of disk array is normal.
The... (4 Replies)
Discussion started by: JoyOnLine
4 Replies
4. SCO
I'm "attempting" to install SCO 5.0.7 on an HP ML370 G4 server and am ready to bash the keyboard with head now. I keep getting the error message "WARNING hd: no root disk controller found" when running the bootable install cd.
I have a raid 5 array with an online spare created using 4 36.3 GB... (2 Replies)
Discussion started by: FrictionBurn
2 Replies
5. Solaris
hi all
i am using vxvm 5.1 on my sun blade 150 which is running with solaris 5.10. When i give the command "vxdisk list" it gives the following output
# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online... (2 Replies)
Discussion started by: kingston
2 Replies
6. SCO
So today I tried to upgrade a customer from a Proliant with an HPSAS controller to an Intel server with a MEGASAS controller.
First, I downloaded the megasas driver from SCO and installed it on the old system.
Then I created a new Microlite Edge emergency boot cd with the new driver on it.
I... (2 Replies)
Discussion started by: jgt
2 Replies
7. Solaris
I changed disk controller. Unplugged every disk, inserted another controller card, an IBM M1015. The disks are recognized in BIOS, and the controller card's BIOS shows up. But after that, I drop into GRUB and a prompt. That is all.
How shall I solve this problem? I am thinking of booting from... (2 Replies)
Discussion started by: kebabbert
2 Replies
8. Solaris
Hi All
Hope it's okay to post on this sub-forum, couldn't find a better place
I've got a 480R running solaris 8 with veritas volume manager managing all filesystems, including an encapsulated root disk (I believe the root disk is encapsulated as one of the root mirror disks has an entry under... (1 Reply)
Discussion started by: sunnyd76
1 Replies
9. Solaris
Hi
The scenario in the oracle t4-1 hardware with solaris 10 is as follows:
1. The initial install on the server was performed with an incorrect disk layout.
2. New disks were ordered and slot into the server.
3. The disks are allocated a controller and a disk number based on the disk or... (13 Replies)
Discussion started by: kerrygold
13 Replies
10. Solaris
Hi,
I have a Sun Fire V440 server that fails to boot up correctly. A lot of services are not started and the sytems acts really slow to commands. During boot I can see the following Error:
WARNING: /pci@1f,700000/scsi@2/sd@0,0 (sd1):
SCSI transport failed: reason 'reset': retrying... (15 Replies)
Discussion started by: oliwei
15 Replies
WREN(3) Library Functions Manual WREN(3)
NAME
wren, ata - hard disk interface
SYNOPSIS
bind #H[drive] /dev
bind #w[target[.lun]] /dev
/dev/hd0disk
/dev/hd0partition
/dev/sd0disk
/dev/sd0partition
...
DESCRIPTION
The hard disk interfaces (wren, #w, is a SCSI disk; ata, #H, is an IDE or ATA disk) serve a one-level directory giving access to the hard
disk partitions. The parameter to attach defines the numerical SCSI target and logical unit number or the IDE drive number to access.
Both default to zero.
Each partition name is prefixed by hd and the numeric drive identifier. The partition always exists and covers the entire disk. The size
of each partition as reported by stat(2) is the number of bytes in the partition, so the size of is the size of the entire disk.
The partition also always exists; it is the last block on the disk for SCSI, second to last for IDE. If it contains valid partition data,
those partitions will be visible as well. Every time the device is bound, the partitions are updated to reflect any changes in the parti-
tion file.
The format of the partition file is the string
plan9 partitions
on a line, followed by partition specifications, one per line, consisting of a name and textual strings for the block start and limit for
each partition on the disk.
The program prep(8) writes the partition table for the disk; its use is preferred to writing it by hand.
SEE ALSO
prep(8), scsi(3)
SOURCE
/sys/src/9/port/devwren.c
/sys/src/9/pc/devata.c
WREN(3)