Sponsored Content
Top Forums UNIX for Advanced & Expert Users Old XFree86 configuration error Post 302351367 by vbe on Tuesday 8th of September 2009 11:23:45 AM
Old 09-08-2009
I had to do my own driver at the time (ET4000...). and I spend a whole weekend testing...
with the source you had a procedure to calculate the width etc...so you will need a pocket calculator with you...

---------- Post updated at 17:20 ---------- Previous update was at 16:02 ----------

Did you look here?
Getting Help with XFree86

---------- Post updated at 17:23 ---------- Previous update was at 17:20 ----------

Resources for XFree86
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

xfree86 configuration

I've been trying to configure XFree86, and the first times that I have, it will only run at 320x? resolution.. I have an ATI card, and I've tried using the /stand/sysinstall graphical configuration method, and I've tried xf86config as well, both render the same results. that was before i... (3 Replies)
Discussion started by: adn
3 Replies

2. Programming

XFree86

So where do we post questions about developing for X? Or do we just not do that here? (2 Replies)
Discussion started by: Gekko
2 Replies

3. UNIX Desktop Questions & Answers

XFREE86 4.2 question

Hi folkss... I just install Freebsd 4.5 mini disk which install only the core FREEBSD system nothing else. I then want to install KDE 3.0 so I install XFREE86 4.2 and I installed both of these programs successfully with pkg_add "filename.tgz" I also install wrapper.tgz for "startx"... (1 Reply)
Discussion started by: helpme2
1 Replies

4. UNIX Desktop Questions & Answers

Installing XFREE86 4.2 question

Hi folksss.. I will ask similiar to my previous post. Have anyone successfully install XFree86 ver. 4.2 on FREEBSD 4.5 from scratch ??? If U do, please provide step by step how U do it. Do U use graphic user interface to setup the hardware configuration or DOS configuration ? I... (2 Replies)
Discussion started by: helpme2
2 Replies

5. UNIX for Dummies Questions & Answers

compiling XFRee86 4.2.0

i am currently trying to compile XFree86 under redhat 7.3. i am used to ./configure make make install, but i know that xfree86 is very different. what are the basic steps for building it. i already have read the documentation, but it wasn't of much help. it was erroring out on the imake. i don't... (1 Reply)
Discussion started by: choasforages
1 Replies

6. UNIX Desktop Questions & Answers

X.Org and XFree86

X.Org just released a new version of their X (X11R6.7). Besides Liscense stuff, what is better about X.org then XFree? What is better about XFree then X.org? Also: Will my fglrx (ATI) or nvidia drivers (designed for XFree86 4.3) work on X.org? (2 Replies)
Discussion started by: punkrockguy318
2 Replies

7. BSD

Problems with Xfree86

Hi to all! I'm very novice in Unix/Linux. I installed FreeBSD 4.10 in my pentium II 450mhz 64MB 4.300GB more than 5 times and the error continues... In the line mode i type "startx" (to enter in X)...but show me a message : FATAL SERVER ERROR NO SCREENS FOUND X CONNECTION TO :0.0... (6 Replies)
Discussion started by: israel
6 Replies

8. BSD

again XFree86

hi everybody i installed FreeBSD 5.x on a box with a video card Diamond SpeedStar A90 and a Fujitsu Siemens Monitor B772-1 when i do "startx" it gives me something like this: fatal error: no devices detected no screen detected i'm lost...i don't know what to... (3 Replies)
Discussion started by: hmaiida
3 Replies

9. BSD

XFree86 4.5 problem

Hello, i have a S3 Trio64V+ card. I installed last release of XFree under FreeBSD 5.4. I do xf86config, but when i try startx i have this error: nsinternal# startx XFree86 Version 4.5.0 Release Date: 16 March 2005 X Protocol Version 11, Revision 0 Build Operating System: FreeBSD... (1 Reply)
Discussion started by: jamesf
1 Replies

10. Programming

xlib blues (XFree86 - Linux)

My goal is to open a window in the X-server and plot a series of pixels. However, I find many examples I have tried to draw to a window fail and the window remains blank. Therefore, I am here requesting information. I do not know c, and am a beginner. Currently, I am using a mix-match of code,... (1 Reply)
Discussion started by: Alux
1 Replies
Ns_Url(3aolserver)					   AOLserver Library Procedures 					Ns_Url(3aolserver)

__________________________________________________________________________________________________________________________________________________

NAME
Ns_AbsoluteUrl, Ns_ParseUrl, Ns_RelativeUrl, Ns_SkipUrl - URL manipulation routines SYNOPSIS
#include "ns.h" int Ns_AbsoluteUrl(Ns_DString *pds, char *url, char *baseurl) int Ns_ParseUrl(char *url, char **pprotocol, char **phost, char **pport, char **ppath, char **ptail) char * Ns_RelativeUrl(char *url, char *location) char * Ns_SkipUrl(Ns_Request *request, int n) _________________________________________________________________ DESCRIPTION
Ns_AbsoluteUrl(pds, url, baseurl) Construct an URL based on baseurl but with as many parts of the incomplete url as possible. Return NS_OK or NS_ERROR. Ns_ParseUrl(url, pprotocol, phost, pport, ppath, ptail) Parse a URL into its component parts. Pointers to the protocol, host, port, path, and "tail" (last path element) will be set by ref- erence in the passed-in pointers. The passed-in url will be modified. Ns_RelativeUrl(url, location) If the url passed in is for this server, then the initial part of the URL is stripped off. e.g., on a server whose location is http://www.foo.com, Ns_RelativeUrl of "http://www.foo.com/hello" will return "/hello". Returns a pointer to the beginning of the relative url in the passed-in url, or NULL if error. Will set errno on error. Ns_SkipUrl(request, n) Return a pointer n elements into the request's url. SEE ALSO
nsd(1), info(n) KEYWORDS
AOLserver 4.0 Ns_Url(3aolserver)
All times are GMT -4. The time now is 01:06 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy