08-25-2009
Hey,
i think your device is not a sun standard device like ce0....
You can show your devices by dladm show-dev, then plumb
the founded devices.
cu
lowbyte
9 More Discussions You Might Find Interesting
1. IP Networking
Hi Folks,
I've just installed solaris 8, but i cannot add my network card.
i've reboot the box, got into the configmode, and try'd to add a network card. but it doesn't work. I can't add a ip address to the card, an error occurs. Who do i add it.
Kind Regards (3 Replies)
Discussion started by: noripsni
3 Replies
2. Solaris
Hello,
I have just installed Solaris 9 x86 in a VMWare and the 1st problem I have is to enable the networking. I can only see the loopback interface and nothing else.
- I dont have any /etc/hostnames.xxx
- ifconfig -a shows only the loopback
- kstat -c net shows only the loopback ...
Any... (11 Replies)
Discussion started by: Tex-Twil
11 Replies
3. Solaris
Installed solaris 10 and now i want to connect to internet,to make work this i need to NIC drivers can some body tell me is it possible to get drivers and how to install. I am dying to get rid of this problem..please help me (1 Reply)
Discussion started by: srinivas2828
1 Replies
4. Solaris
Dear all,
I am a newbie in solaris and I need your advice.
I have a Solaris version 5.9 installed on Sunfire V240.
I am able to ssh the machine from putty remotely.
My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies
5. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. Solaris
hi guys,
is there any way to change the nic link_speed in Solaris 10? now my box is running degraded performance of the link speed as the switch is upgraded from 100m to 1000m.
dladm show-dev
e1000g0 link: up speed: 100 Mbps duplex: full
e1000g1 link: up ... (10 Replies)
Discussion started by: freshmeat
10 Replies
8. AIX
Hi,
is there any method to check the interface collisions on ethernet NIC in AIX. I know that in Solaris it's netstat -i but I've written that in AIX it doesn't show this.
Thanks®ards,
p (1 Reply)
Discussion started by: pitmod
1 Replies
9. Solaris
Hi All
I would need to do hard code of nxge0 nic to full duplex & 1000mbps. So that whenever solaris server come up after reboot. it will show full duplex & 1000mbps setting only.
Please also let me know how to do it online through command.
regards (0 Replies)
Discussion started by: amity
0 Replies
SET_NET_DEFAULT(8) System Manager's Manual SET_NET_DEFAULT(8)
NAME
s_n_d, set_net_default - select the default TCP/IP network
SYNOPSIS
set_net_default: not found
DESCRIPTION
This manual page is here because so many others refer to it. The set_net_default command does not exist under standard Minix, because the
TCP/IP server only supports one network. The server under Minix-vmd supports four different networks, that can each be chosen as the
default network.
The TCP/IP library and commands do have a notion about a "default network" however, because the code is shared between the Minix versions.
So if you want to venture into network programming then you should know about the devices and environment variables mentioned below to make
your program compatible. (Especially since there is a plan to upgrade the TCP/IP server for standard Minix.)
Options and environment to change the default
Many TCP/IP programs implement the following options and environment variables to change the default devices set by set_net_default. The
options are only implemented for low level programs where it makes sense to name a network device. The environment variables are used in
all code. You can run a process and all its children connected to a different network by setting four environment variables.
ETH_DEVICE=device
-E device
Device to use as raw ethernet device instead of the default /dev/eth.
PSIP_DEVICE=device
-P device
Pseudo IP device to use instead of /dev/psip.
IP_DEVICE=device
-I device
IP device to use instead of /dev/ip.
TCP_DEVICE=device
-T device
TCP device to use.
UDP_DEVICE=device
-U device
UDP device to use.
FILES
/dev/eth[01] First and second raw ethernet.
/dev/psip[01] First and second Pseudo IP network.
/dev/ip[0123] IP devices for two ethernets and two Pseudo IP networks.
/dev/tcp[0123] TCP devices for same four networks.
/dev/udp[0123] UDP devices.
/dev/eth, /dev/psip, /dev/ip, /dev/tcp, /dev/udp
Devices for the default network, links to the devices above. Eth is only present if ethernet is the default, psip only
for pseudo IP.
SEE ALSO
ip(4), boot(8).
AUTHOR
Kees J. Bot (kjb@cs.vu.nl)
SET_NET_DEFAULT(8)