08-19-2009
data loss inevitable?
Quote:
Originally Posted by
Sun Fire
I'm not sure if it's going to recognize the RAID and Data on it or not, because if you attempt to create new RAID array, it will initialize and wipe out your data.
Yep. To actually be able to use the disks for RAID in SE3310, the admin would need to "deinitialize" the disks first.
Quote:
Best bet is, backup your data before you do this movement, and
That sounds kinda awkward - suppose the array breaks (but the disks don't). In that case, the data is lost? Doesn't sound too professional to me... I mean, yes, of course you do backups, sure. But at least I only do one backup per day. If the array breaks shortly before the backup starts, then one day of work is lost.
Hard to imagine that Sun really wants its users to go that route.
Quote:
also backup the current storage configuration file .xml
What XML file? The RAID is configured and setup from "inside" the SE3310 over the telnet interface.
10 More Discussions You Might Find Interesting
1. Solaris
Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000"
the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies
2. Solaris
Hello,
I have a d1000, it's connected to two servers, I want both servers to see all disks in the array. i.e. i have 6 disks, 3 in each side, I want both servers to see all 6 disks.
It appears to be setup in a split bus mode now, ive looked thru the manuals and have become confused!
So,... (2 Replies)
Discussion started by: BG_JrAdmin
2 Replies
3. Red Hat
We have a Red Hat linux server running on IBM x445 hardware. There are external disks in an IBM EXP300 disk enclosure. The system is running RAID 5. One of the four IBM disks (73.4 GB 10k FRU 06P5760) has become faulty. The system is still up and running OK because of the RAID. In that same EXP300... (3 Replies)
Discussion started by: pdudley
3 Replies
4. Solaris
HI guys.
Bit of a noob so bear with me.
I have 2 new disks I want to add to my StorEdge 3310 but am getting lost in the steps. We have another 3310 (JBOD) that I was able to plug the disks into and they instantly showed up. Did a few minor commands after (drvconfig, devfsadm etc..) and I was... (4 Replies)
Discussion started by: jamie_collins
4 Replies
5. Solaris
I've just installed Sol 10 Update 9 on a Sun 4140 server and have a RAID 1 configuration (2 136 Gb drives) for the OS and have created a RAID 5 array (6 136 GB) drives. When i log into the system I am unable to see the RAID 5 disks at all. I've tried using the devfsadm command but no luck and... (9 Replies)
Discussion started by: goose25
9 Replies
6. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
7. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
8. Solaris
Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes.
Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies
9. Solaris
Dear All ,
Pl find the below command ,
# raidctl -l
Controller: 1
Volume:c1t0d0
Disk: 0.0.0
Disk: 0.1.0
Disk: 0.3.0
#
raidctl -l c1t0d0
Volume Size Stripe Status Cache RAID
Sub Size ... (10 Replies)
Discussion started by: jegaraman
10 Replies
10. Shell Programming and Scripting
The below will move all the files in the directory dir to the destination using parallel and create a log, however will not keep them in the directory. I have tried mkdir -p but that does not seem to work or at least I can not seem to get it (as it deletes others files when I use it). What is the... (2 Replies)
Discussion started by: cmccabe
2 Replies
LEARN ABOUT REDHAT
raidstart
raidstart(8) System Manager's Manual raidstart(8)
NAME
raidstart, raidstop, - command set to manage md devices.
SYNOPSIS
raidstart [options] <raiddevice>*
raidstop [options] <raiddevice>*
DESCRIPTION
RAID devices are virtual devices created from two or more real block devices. This allows multiple disks to be combined into a single
filesystem, possibly with automated backup and recovery. Linux RAID devices are implemented through the md device driver.
If you're using the /proc filesystem, /proc/mdstat gives you informations about md devices status.
Currently, Linux supports linear md devices, RAID0 (striping), RAID1 (mirrroring), and RAID4 and RAID5. For information on the various lev-
els of RAID, check out:
http://ostenfeld.dk/~jakob/Software-RAID.HOWTO/
for new releases of the RAID driver check out:
ftp://ftp.fi.kernel.org/pub/linux/daemons/raid/alpha
Avaible commands are :
mkraid : configures (creates) md (RAID) devices in the kernel, banding multiple devices into one.
raidstart : activates (starts) an existing 'persistent' md device
raid0run : activates old nonpersistent RAID0/LINEAR md devices
raidstop : turns off an md device, and unconfigures (stops) it
By default, a systems RAID configuration is kept in /etc/raidtab, which can configure multiple RAID devices.
All of these tools work similiarly. If -a (or --all) is specified, the specified operation is performed on all of the RAID devices men-
tioned in the configuration file. Otherwise, one or more RAID devices must be specified on the command line. For example:
raid0run -a
Starts all of the 'old' RAID0 RAID devices specified in /etc/raidtab. If only /dev/md1 should be started, the following command should be
used instead:
raidstart /dev/md1
OPTIONS
-a, --all
Apply the command to all of the configurations specified in the config file.
-c, --configfile filename
Use filename as the configuration file (/etc/raidtab is used by default).
-h, --help
Displays a short usage message, then exits.
-V, --version
Displays a short version message, then exits.
NOTES
The raidtools are derived from the md-tools and raidtools packages, which were originally written by Marc Zyngier, Miguel de Icaza, Gadi
Oxman, Bradley Ward Allen, and Ingo Molnar.
BUGS
no known bugs.
SEE ALSO
raidtab(5), raid0run(8), raidstop(8), mkraid(8)
raidstart(8)