How to active this network adapter? Post: 302343808

10 More Discussions You Might Find Interesting

1. Solaris

Sun v440/v880 network adapter teaming

Is it possible to team two network adapters for fault tolerance in a Sun v440 or v880 Solaris 8 box? If so how would I go about doing so?

2. AIX

hacmp network adapter re-define

I have an LPAR in a P5 machine which has been setup in an HACMP cluster. The person who set it up allocated the wrong network adapter (en) to the persistent network. For the life of me I cannot find where I can re-assign this adapter. Anyone able to help me as I am tearing my hair out and do not...

3. AIX

change network adapter

hello i've need to change network adapter on machine H80 aix 4.3.3 hacmp ( ent0 ) what i need to do after the new adapter installed on the machine? thanks best regards ariec

4. UNIX for Dummies Questions & Answers

External Network Adapter for Solaris 10

Hi All, I am new here - this is my first post. I have installed Solaris 10 5/09 on my Dell M6300. The install went well, but the Dell's onboard network card is the Broadcom BCM5756ME Gigabit Ethernet - and sadly no Solaris driver exists for it. The Solaris 10 install just jumped by the...

5. IP Networking

Maximum IP Address Configured on Intel Network Adapter

Hi All, Sorry if this is not the correct forum to answer. But hope somebody can help me... For these two types of network adapter: Intel(R) PRO/1000 MT Server Adapter Intel(R) PRO/1000 MT Dual Port Network Adapter How many IP addresses can be configured on it at the same time? System...

6. UNIX for Dummies Questions & Answers

SCO Unixware 7.1.4 Network Adapter Error

Hi All I P2Vd a Unixware 7.1.4 box with VMWare Vsphere. I try to add a network adapter under Network Configuration Manager and it comes up with the error attached. I've added a virtual adapter using the "E1000" option. It detects both the AMD PCI NET and E1000 virtual adapters under Network...

7. UNIX for Dummies Questions & Answers

Simulated driver for Network Interface Adapter

Hi all, I got sort of a task to do. I have to write in C "simulated network driver". What does it mean? - It has to run on all network adapters - It has to be as simple as it can be - It has to run on all linux distributions (or at least most of them) - It does not have to run a network...

8. Programming

Compiling virtual network adapter driver problem (net_device struct)

Hi, I found on linuxgazette.net/93/bhaskaran.html page very useful sample of virtual driver (not connected to real hardware). I try to compile it with no effect. So: I got fresh Ubuntu 9.10 (kernel 2.6.31-14) My source is saved in networkAdapter.c file in /usr/src/myModules directory. I...

9. Hardware

Problematic RTL8188EE Wireless Network Adapter

Good Day All, There are numerous results when searching google on this issue, however, none seem to have a solution. I have read until my eyes bleed and banged my head on the table more than once! :) I am hoping to resolve this issue -- or at least have a decent workaround. It is a real...

10. SCO

Can not recognize network adapter SCO UNIX in HP z400

hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback. show message : dlpid:unable to open network adapter driver...

LEARN ABOUT OPENDARWIN

traceroute6

TRACEROUTE6(8)						    BSD System Manager's Manual 					    TRACEROUTE6(8)

NAME

     traceroute6 -- print the route IPv6 packets will take to the destination

SYNOPSIS

     traceroute6 [-dlnrv] [-f firsthop] [-g gateway] [-m hoplimit] [-p port] [-q probes] [-s src] [-w waittime] target [datalen]

DESCRIPTION

     -d      Debug mode.

     -f firsthop
	     Specify how many hops to skip in trace.

     -g gateway
	     Specify intermediate gateway (traceroute6 uses routing header).

     -m hoplimit
	     Specify maximum hoplimit.

     -l      Print both host hostnames and numeric addresses.  Normally traceroute6 prints only hostnames if -n is not specified, and only numeric
	     addresses if -n is specified.

     -n      Do not resolve numeric address to hostname.

     -p port
	     Set UDP port number to port.

     -q probes
	     Set the number of probe per hop count to probes.

     -r

     -s src  Src specifies the source IPv6 address to be used.

     -v      Be verbose.

     -w waittime
	     Specify the delay time between probes.

RETURN VALUES

     The traceroute6 command will exit with 0 on success, and non-zero on errors.

SEE ALSO

     ping(8), ping6(8), traceroute(8)

HISTORY

     The traceroute6 command first appeared in WIDE hydrangea IPv6 protocol stack kit.

BSD
								   May 17, 1998 							       BSD