DIVERT(4)						   BSD Kernel Interfaces Manual 						 DIVERT(4)

NAME

     divert -- kernel packet diversion mechanism

SYNOPSIS

     #include <sys/types.h>
     #include <sys/socket.h>
     #include <netinet/in.h>

     int
     socket(PF_INET, SOCK_RAW, IPPROTO_DIVERT);

DESCRIPTION

     Divert sockets are similar to raw IP sockets, except that they can be bound to a specific divert port via the bind(2) system call.  The IP
     address in the bind is ignored; only the port number is significant.  A divert socket bound to a divert port will receive all packets
     diverted to that port by some (here unspecified) kernel mechanism(s).  Packets may also be written to a divert port, in which case they re-
     enter kernel IP packet processing.

     Divert sockets are normally used in conjunction with FreeBSD's packet filtering implementation and the ipfw(8) program.  By reading from and
     writing to a divert socket, matching packets can be passed through an arbitrary ``filter'' as they travel through the host machine, special
     routing tricks can be done, etc.

READING PACKETS

     Packets are diverted either as they are ``incoming'' or ``outgoing.''  Incoming packets are diverted after reception on an IP interface,
     whereas outgoing packets are diverted before next hop forwarding.

     Diverted packets may be read unaltered via read(2), recv(2), or recvfrom(2).  In the latter case, the address returned will have its port set
     to the some tag supplied by the packet diverter, (usually the ipfw rule number) and the IP address set to the (first) address of the inter-
     face on which the packet was received (if the packet was incoming) or INADDR_ANY (if the packet was outgoing). In the case of an incoming
     packet the interface name will also be placed in the 8 bytes following the address, (assuming it fits).

WRITING PACKETS

     Writing to a divert socket is similar to writing to a raw IP socket; the packet is injected ``as is'' into the normal kernel IP packet pro-
     cessing and minimal error checking is done.  Packets are written as either incoming or outgoing: if write(2) or send(2) is used to deliver
     the packet, or if sendto(2) is used with a destination IP address of INADDR_ANY, then the packet is treated as if it were outgoing, i.e.,
     destined for a non-local address.	Otherwise, the packet is assumed to be incoming and full packet routing is done.

     In the latter case, the IP address specified must match the address of some local interface, or an interface name must be found after the IP
     address.  If an interface name is found, that interface will be used and the value of the IP address will be ignored (other than the fact
     that it is not INADDR_ANY).  This is to indicate on which interface the packet ``arrived.''

     Normally, packets read as incoming should be written as incoming; similarly for outgoing packets.	When reading and then writing back pack-
     ets, passing the same socket address supplied by recvfrom(2) unmodified to sendto(2) simplifies things (see below).

     The port part of the socket address passed to the sendto(2) contains a tag that should be meaningful to the diversion module.  In the case of
     ipfw(8) the tag is interpreted as the rule number after which rule processing should restart.

LOOP AVOIDANCE

     Packets written into a divert socket (using sendto(2)) re-enter the packet filter at the rule number following the tag given in the port part
     of the socket address, which is usually already set at the rule number that caused the diversion (not the next rule if there are several at
     the same number). If the 'tag' is altered to indicate an alternative re-entry point, care should be taken to avoid loops, where the same
     packet is diverted more than once at the same rule.

DETAILS

     To enable divert sockets, your kernel must be compiled with the option IPDIVERT.

     If a packet is diverted but no socket is bound to the port, or if IPDIVERT is not enabled in the kernel, the packet is dropped.

     Incoming packet fragments which get diverted are fully reassembled before delivery; the diversion of any one fragment causes the entire
     packet to get diverted.  If different fragments divert to different ports, then which port ultimately gets chosen is unpredictable.

     Packets are received and sent unchanged, except that packets read as outgoing have invalid IP header checksums, and packets written as outgo-
     ing have their IP header checksums overwritten with the correct value.  Packets written as incoming and having incorrect checksums will be
     dropped.  Otherwise, all header fields are unchanged (and therefore in network order).

     Binding to port numbers less than 1024 requires super-user access, as does creating a socket of type SOCK_RAW.

ERRORS

     Writing to a divert socket can return these errors, along with the usual errors possible when writing raw packets:

     [EINVAL]		The packet had an invalid header, or the IP options in the packet and the socket options set were incompatible.

     [EADDRNOTAVAIL]	The destination address contained an IP address not equal to INADDR_ANY that was not associated with any interface.

SEE ALSO

     bind(2), recvfrom(2), sendto(2), socket(2), ipfw(8)

BUGS

     This is an attempt to provide a clean way for user mode processes to implement various IP tricks like address translation, but it could be
     cleaner, and it's too dependent on ipfw(8).

     It's questionable whether incoming fragments should be reassembled before being diverted.	For example, if only some fragments of a packet
     destined for another machine don't get routed through the local machine, the packet is lost.  This should probably be a settable socket
     option in any case.

AUTHORS

     Archie Cobbs <archie@FreeBSD.org>, Whistle Communications Corp.

BSD
								   June 18, 1996							       BSD