07-23-2009
Is your computer standalone workstation or we talk about server
10 More Discussions You Might Find Interesting
1. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
2. IP Networking
Hello this is my first post at this forum.
Apologize for my lack of network understanding
but Im posting to learn.
I have a problem reaching default gateway 10.18.110.1
If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping.
cat... (11 Replies)
Discussion started by: vettec3
11 Replies
3. AIX
Hello,
I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies
4. Red Hat
I know the subject line is very similar to: destination host unreachable
but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there.
We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies
5. UNIX for Dummies Questions & Answers
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a... (4 Replies)
Discussion started by: Rutgerncas
4 Replies
6. AIX
I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a
startsrc -g tcpip
... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies
7. Red Hat
Hi,
Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies
8. AIX
Hi,
I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure?
Is there anything that I have to check with vio setting or Am I missing any configuration?
Please let me know further.
Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies
9. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)
NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO
mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)