06-18-2009
SCO 6 + Virtualbox 2 == no NIC
Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack 4, then I installed the nd package (twice as outlined in
ftp://ftp.sco.com/pub/openserver6/60...rst_nd_install), and rebooted. What next? netadmin does not seem to allow me to add any of the NICs whose drivers I just installed.
Thanks for any help!
Oh, just to let you all know, the driver for the intel card is installed (as /etc/ints/nd/mdi/e1006g).
Last edited by dalek; 06-19-2009 at 12:15 PM..
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
2. SCO
I have a SCO 5.0.7 server.As there is no parellel port ,printing is done via USB port.
After loading the Network Card driver ,during booting the server gets hanged and the NIC driver is not loaded.If the USB ports are disabled the NIC driver gets loaded.
As both USB and NIC driver are essential... (0 Replies)
Discussion started by: vikramviky
0 Replies
3. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
4. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
5. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
6. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
7. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
8. SCO
Sir I am trying to install UnixWare7.1.4 on vmware workstation9, virtualbox and I am getting the following error
FATAL BOOT ERROR: decompression failed
For installing SCO Unixware7.1.4 I have created virtual harddisk of size 18GB, 1024 RAM, 64bit video memory, chosen unixware7.1.4... (1 Reply)
Discussion started by: rupeshforu3
1 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
LEARN ABOUT FREEBSD
dh_bugfiles
DH_BUGFILES(1) Debhelper DH_BUGFILES(1)
NAME
dh_bugfiles - install bug reporting customization files into package build directories
SYNOPSIS
dh_bugfiles [-A] [debhelperoptions]
DESCRIPTION
dh_bugfiles is a debhelper program that is responsible for installing bug reporting customization files (bug scripts and/or bug control
files and/or presubj files) into package build directories.
FILES
debian/package.bug-script
This is the script to be run by the bug reporting program for generating a bug report template. This file is installed as
usr/share/bug/package in the package build directory if no other types of bug reporting customization files are going to be installed
for the package in question. Otherwise, this file is installed as usr/share/bug/package/script. Finally, the installed script is given
execute permissions.
debian/package.bug-control
It is the bug control file containing some directions for the bug reporting tool. This file is installed as
usr/share/bug/package/control in the package build directory.
debian/package.bug-presubj
The contents of this file are displayed to the user by the bug reporting tool before allowing the user to write a bug report on the
package to the Debian Bug Tracking System. This file is installed as usr/share/bug/package/presubj in the package build directory.
OPTIONS
-A, --all
Install debian/bug-* files to ALL packages acted on when respective debian/package.bug-* files do not exist. Normally, debian/bug-*
will be installed to the first package only.
SEE ALSO
/usr/share/doc/reportbug/README.developers.gz
debhelper(1)
This program is a part of debhelper.
AUTHOR
Modestas Vainius <modestas@vainius.eu>
11.1.6ubuntu2 2018-05-10 DH_BUGFILES(1)