06-09-2009
Hi,
auto-boot-on-error? has already been set to false previously.
Customer has already started questioning the reliability of Sun and hopefully the system board replacement will get this resolved. As you said, perhaps they won't drag this to the max, else...
I will keep looking for the possible solutions. Thank you for your help. Appreciated it much!
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I am fresher in Virtualisation in solaris 10.I need to know how to install and configure guest OS, I have a server Sun T2000 with solaris 10 OS BASE.
How to install logical domain, what are the prerequest for installing l domain
can some one guide me what are the basic requirement to... (2 Replies)
Discussion started by: solaris8in
2 Replies
2. Solaris
I can't find why but I suppose it is because of some hardware failures... I have a Sun Fire V490 with Solaris 10 5/08 which runs Sun Cluster 3.2 and it downs occasionally with a circumstances I can't define... Also I note some strange behavior after server failures: when I ran any diagnostics from... (6 Replies)
Discussion started by: Sapfeer
6 Replies
3. Solaris
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Discussion started by: ouzist
1 Replies
4. Solaris
Hi Guys,
I am unable to turn on the locator led light on a SUN T2000 machine
# uname -a
SunOS node1 5.10 Generic_137137-09 sun4v sparc SUNW,Sun-Fire-T200
when i try to turn it on I have following error.
# locator -n
'system' locator not found
Although the hardware specfication... (5 Replies)
Discussion started by: Asteroid
5 Replies
5. Solaris
This may be a stupid question, but I don't want to take any chances.
I have a Sun T2000 in production. I want to run the "resetsc" command on the ALOM controller to active an IP address change. Will resetting ALOM affect the running OS?
Thanks (2 Replies)
Discussion started by: soliberus
2 Replies
6. Hardware
Hi All
I have a Sun T2000 server. Couple of years ago I had configured and mirrored the boot drive with an other drive using hardware RAID 1 using raidctl command.
Following is the hardware RAID output.
root@oracledatabaseserver / $ raidctl
RAID Volume RAID RAID Disk... (0 Replies)
Discussion started by: Tirmazi
0 Replies
7. Solaris
I got a Power supply failure. I replaced the power supply and still got the error.
Any ideas on what I should try next? (1 Reply)
Discussion started by: 642fiddi
1 Replies
8. Solaris
Hi,
Would like to know the uptime or specific time limit to reboot the sun microsystem to avoid unplanned outage.
Regards,Tarun (9 Replies)
Discussion started by: taruntan
9 Replies
9. Solaris
Hi folks,
I was patching Sun server (SunOS suns121 5.10 Generic_144488-17 sun4v sparc SUNW,Sun-Fire-T200) with the lateset bundle. It was completed with no errors. Server was restarted with shutdown command
(/usr/sbin/shutdown -y -i6 -g0) after patching was complete. However, after that,... (3 Replies)
Discussion started by: zulu1
3 Replies
10. Solaris
==============================
ALOM BOOTMON v1.3.1
ALOM Build Release: 001
Reset register: f0000000 EHRS ESRS LLRS SWRS
ALOM POST 1.0
Dual Port Memory Test, PASSED.
TTY External - Internal Loopback Test
TTY External - Internal Loopback Test, PASSED.
TTYC - Internal Loopback Test
TTYC -... (4 Replies)
Discussion started by: Sameer Naik
4 Replies
HME(4) BSD Kernel Interfaces Manual HME(4)
NAME
hme -- Sun Microelectronics STP2002-STQ Ethernet interfaces device driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
device miibus
device hme
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_hme_load="YES"
DESCRIPTION
The hme driver supports Sun Microelectronics STP2002-STQ ``Happy Meal Ethernet'' Fast Ethernet interfaces.
All controllers supported by the hme driver have TCP checksum offload capability for both receive and transmit, support for the reception and
transmission of extended frames for vlan(4) and a 128-bit multicast hash filter.
HARDWARE
The hme driver supports the on-board Ethernet interfaces of many Sun UltraSPARC workstation and server models.
Cards supported by the hme driver include:
o Sun PCI SunSwift Adapter (``SUNW,hme'')
o Sun SBus SunSwift Adapter (``hme'' and ``SUNW,hme'')
o Sun PCI Sun100BaseT Adapter 2.0 (``SUNW,hme'')
o Sun SBus Sun100BaseT 2.0 (``SUNW,hme'')
o Sun PCI Quad FastEthernet Controller (``SUNW,qfe'')
o Sun SBus Quad FastEthernet Controller (``SUNW,qfe'')
NOTES
On sparc64 the hme driver respects the local-mac-address? system configuration variable which can be set in the Open Firmware boot monitor
using the setenv command or by eeprom(8). If set to ``false'' (the default), the hme driver will use the system's default MAC address for
all of its devices. If set to ``true'', the unique MAC address of each interface is used if present rather than the system's default MAC
address.
Supported interfaces having their own MAC address include on-board versions on boards equipped with more than one Ethernet interface and all
add-on cards except the single-port SBus versions.
SEE ALSO
altq(4), intro(4), miibus(4), netintro(4), vlan(4), eeprom(8), ifconfig(8)
Sun Microelectronics, STP2002QFP Fast Ethernet, Parallel Port, SCSI (FEPS) User's Guide, April 1996,
http://mediacast.sun.com/users/Barton808/media/STP2002QFP-FEPs_UG.pdf.
HISTORY
The hme driver first appeared in NetBSD 1.5. The first FreeBSD version to include it was FreeBSD 5.0.
AUTHORS
The hme driver was written by Paul Kranenburg <pk@NetBSD.org>.
BSD June 14, 2009 BSD