ethernet Post: 302321115

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Ethernet

We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time...

2. UNIX for Dummies Questions & Answers

Ethernet Initialisation

I am using Red Hat 7.1 . I have installed one Server and trying to make network installing workstations on other system of a network. The Ethernet of the server has been mounted and working properly. I am getting problem installing /mounting the Ethernet of the workstations .I have tryed this by...

3. Cybersecurity

Ethernet sniff.

I suspect that someone is using a sniffer on my Ethernet connection, OS X 10.3.9, DSL, ok, I'm in terminal using the "ifconfig" command > flags=8049<UP,LOOPBACK,RUNNING,MULTICAST>mtu 16384 right, it's not in "promiscuous mode", but i think it's Trojaned, can anyone point me in the...

4. UNIX for Advanced & Expert Users

Virtual Ethernet

I understand that one should setup virtual ethernet adapters in the lpars which is the best way for various lpars to communicate with each other - Does anyone have info on this or can point me to a doc that explains how to set this up?

5. IP Networking

ethernet card

What command do I use to show mw the ethernet card, I have tried ipconfig -a

6. Solaris

ethernet problem

Boot device: /pci@8,600000/SUNW,qlc@4/fp@0,0/disk@w500000e0103c3391,0:a File and args: SunOS Release 5.8 Version Generic_108528-29 64-bit Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved. ifconfig: plumb: qfe2: Bad file number configuring IPv4 interfaces: eri0. moving addresses...

7. AIX

ethernet down

Hello everyone I have a problem with one server, has Aix 5.3 in the errpt has this message IDENTIFIER TIMESTAMP T C RESOURCE_NAME DESCRIPTION F3931284 0105133009 I H ent0 ETHERNET NETWORK RECOVERY MODE EC0BCCD4 0105133009 T H ent0 ETHERNET DOWN F3931284 ...

8. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter...

9. Linux

ethernet bonding

I need to enable Ethernet Bonding on three systems, connected together via switch. What I tried ended up with failure, slaves cannot be detected n added to bon0. Here's what I did: created file /etc/modprobe.d/bonding.d and added the following to it: alias bond0 bonding options bonding...

LEARN ABOUT MOJAVE

git-prune

GIT-PRUNE(1)                                                        Git Manual                                                        GIT-PRUNE(1)

NAME

       git-prune - Prune all unreachable objects from the object database

SYNOPSIS

       git prune [-n] [-v] [--progress] [--expire <time>] [--] [<head>...]

DESCRIPTION

           Note
           In most cases, users should run git gc, which calls git prune. See the section "NOTES", below.

       This runs git fsck --unreachable using all the refs available in refs/, optionally with additional set of objects specified on the command
       line, and prunes all unpacked objects unreachable from any of these head objects from the object database. In addition, it prunes the
       unpacked objects that are also found in packs by running git prune-packed. It also removes entries from .git/shallow that are not reachable
       by any ref.

       Note that unreachable, packed objects will remain. If this is not desired, see git-repack(1).

OPTIONS

       -n, --dry-run
           Do not remove anything; just report what it would remove.

       -v, --verbose
           Report all removed objects.

       --progress
           Show progress.

       --expire <time>
           Only expire loose objects older than <time>.

       --
           Do not interpret any more arguments as options.

       <head>...
           In addition to objects reachable from any of our references, keep objects reachable from listed <head>s.

EXAMPLE

       To prune objects not used by your repository or another that borrows from your repository via its .git/objects/info/alternates:

           $ git prune $(cd ../another && git rev-parse --all)

NOTES

       In most cases, users will not need to call git prune directly, but should instead call git gc, which handles pruning along with many other
       housekeeping tasks.

       For a description of which objects are considered for pruning, see git fsck's --unreachable option.

SEE ALSO

       git-fsck(1), git-gc(1), git-reflog(1)

GIT

       Part of the git(1) suite

Git 2.17.1                                                          10/05/2018                                                        GIT-PRUNE(1)