Sponsored Content
Full Discussion: POWER6 VIO Failover
Operating Systems AIX POWER6 VIO Failover Post 302319477 by funksen on Monday 25th of May 2009 10:40:05 AM
Old 05-25-2009
are the luns mapped to a vhost?

if yes and the client partitions are off as you wrote, use rmdev -dev vtdname -ucfg on the vtd
change reserve_policy and run cfgdev, then the vtds are available again



and you need to reboot the vio-server after installing the sddpcm drivers
 

9 More Discussions You Might Find Interesting

1. AIX

Oracle 10G best practices on Power6 AIX5.3

Can anyone point me to any best practices for partitioning, resource prerequisites, and implementation of Oracle 10G release 2 with RAC on 2 power6 550's running AIX5.3 as a cluster? (1 Reply)
Discussion started by: JodyTek
1 Replies

2. AIX

Power6 Virtual Fibre Channel Adapter

Hello, Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter. It is similar to virtual scsi adapter. In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies

3. AIX

vio server and vio client

Hi, I want to know wheather partition size for installation of vio client can be specified on vio server example If I am installing vio server on blade with 2*300gb hard disk,after that I want to create 2 vio client (AIX Operating system) wheather I can specify hard disk size while... (1 Reply)
Discussion started by: manoj.solaris
1 Replies

4. AIX

AIX 6.1 Power6 - Sys CPU utilization twice that of User

Hello, We just purchased two new 4-way (one active one failover) 5Ghz Power6 Servers (failover) with 64GB RAM (32GB per node) runing AIX 6.1 with two LPARs per node connected to our SAN with two 4GB HBAs. The PROD LPAR has 2 dedicated CPUs (4 virtual) and the TEST LPAR has 2 dedicated CPUs. ... (3 Replies)
Discussion started by: troym72
3 Replies

5. AIX

HACMP with VIO, service IP failover

Would anyone please kindly help to solve this problem... An LPAR with the below network configuration. ent0 and ent1 are logical lan (virtual ethernet) from VIO SEA. en0 1.2.3.4 <- boot ip 192.168.1.1 <- persistent ip 192.168.1.10 <- service ip en1 11.22.33.44 <- boot ip When I... (6 Replies)
Discussion started by: skeyeung
6 Replies

6. AIX

vio server ethernet to vio client ethernet(concepts confusing)

Hi In the vio server when I do # lsattr -El hdisk*, I get a PVID. The same PVID is also seen when I put the lspv command on the vio client partition. This way Im able to confirm the lun using the PVID. Similarly how does the vio client partition gets the virtual ethernet scsi client adapter... (1 Reply)
Discussion started by: newtoaixos
1 Replies

7. AIX

Power6 vs. Power7 hardware performance

I know I will get blasted for posting here, not know where to post this, however, I have performance question between the 2 platforms. Not knowing the exact processors in each box, but the Power6 Platform clock speed is 4400 (?? at least what was told to me), and the Power7 clock speed is 3500.... (5 Replies)
Discussion started by: mrmurdock
5 Replies

8. AIX

How to get power6 power FRU?

how to get power6 power FRU? the power5 can get by this command: lscfg -vp | grep -p 'AC PS' | grep FRU however, the power6 machine cannot get any info for that command. thanks (1 Reply)
Discussion started by: rainbow_bean
1 Replies

9. AIX

Hard drive compatibility for POWER6 p520

Hi, I have recently inherited an old p520 from work running AIX 6.1, based on the POWER6 CPU. I'm planning to play around with it and use it to learn the system, so this is a purely personal project. The machine is not under a support contract any more. I am looking to replace one of the disks... (11 Replies)
Discussion started by: topcat
11 Replies
HD(4)							     Linux Programmer's Manual							     HD(4)

NAME
hd - MFM/IDE hard disk devices DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave hdd. General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi- cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions on an IDE disk. For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the second one. They are typically created by: mknod -m 660 /dev/hda b 3 0 mknod -m 660 /dev/hda1 b 3 1 mknod -m 660 /dev/hda2 b 3 2 ... mknod -m 660 /dev/hda8 b 3 8 mknod -m 660 /dev/hdb b 3 64 mknod -m 660 /dev/hdb1 b 3 65 mknod -m 660 /dev/hdb2 b 3 66 ... mknod -m 660 /dev/hdb8 b 3 72 chown root:disk /dev/hd* FILES
/dev/hd* SEE ALSO
chown(1), mknod(1), sd(4), mount(8) COLOPHON
This page is part of release 3.25 of the Linux man-pages project. A description of the project, and information about reporting bugs, can be found at http://www.kernel.org/doc/man-pages/. Linux 1992-12-17 HD(4)
All times are GMT -4. The time now is 10:37 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy