thats interesting...you are right, I have checked the outputs of systems I set up, and looks like after firmware upgrade it gives more comprehensive information.
this is the output of one T5220, and firmware is up to date
Code:
System Configuration: Sun Microsystems sun4v SPARC Enterprise T2000
Memory size: 8064 Megabytes
================================ Virtual CPUs ================================
CPU ID Frequency Implementation Status
------ --------- ---------------------- -------
0 1000 MHz SUNW,UltraSPARC-T1 on-line
1 1000 MHz SUNW,UltraSPARC-T1 on-line
2 1000 MHz SUNW,UltraSPARC-T1 on-line
3 1000 MHz SUNW,UltraSPARC-T1 on-line
4 1000 MHz SUNW,UltraSPARC-T1 on-line
5 1000 MHz SUNW,UltraSPARC-T1 on-line
6 1000 MHz SUNW,UltraSPARC-T1 on-line
7 1000 MHz SUNW,UltraSPARC-T1 on-line
8 1000 MHz SUNW,UltraSPARC-T1 on-line
9 1000 MHz SUNW,UltraSPARC-T1 on-line
10 1000 MHz SUNW,UltraSPARC-T1 on-line
11 1000 MHz SUNW,UltraSPARC-T1 on-line
12 1000 MHz SUNW,UltraSPARC-T1 on-line
13 1000 MHz SUNW,UltraSPARC-T1 on-line
14 1000 MHz SUNW,UltraSPARC-T1 on-line
15 1000 MHz SUNW,UltraSPARC-T1 on-line
======================= Physical Memory Configuration ========================
Segment Table:
--------------------------------------------------------------
Base Segment Interleave Bank Contains
Address Size Factor Size Modules
--------------------------------------------------------------
0x0 8 GB 4 2 GB MB/CMP0/CH0/R0/D0
MB/CMP0/CH0/R0/D1
2 GB MB/CMP0/CH1/R0/D0
MB/CMP0/CH1/R0/D1
2 GB MB/CMP0/CH2/R0/D0
MB/CMP0/CH2/R0/D1
2 GB MB/CMP0/CH3/R0/D0
MB/CMP0/CH3/R0/D1
========================= IO Configuration =========================
IO
Location Type Slot Path Name Model
----------- ----- ---- --------------------------------------------- ------------------------- ---------
IOBD/NET0 PCIE IOBD /pci@780/pci@0/pci@1/network@0 network-pciex8086,105e
IOBD/NET1 PCIE IOBD /pci@780/pci@0/pci@1/network@0,1 network-pciex8086,105e
IOBD/PCIE PCIE IOBD /pci@780/pci@0/pci@9/scsi@0 scsi-pciex1000,56 LSI,1064E
IOBD/NET2 PCIE IOBD /pci@7c0/pci@0/pci@2/network@0 network-pciex8086,105e
IOBD/NET3 PCIE IOBD /pci@7c0/pci@0/pci@2/network@0,1 network-pciex8086,105e
IOBD/PCIX PCIX IOBD /pci@7c0/pci@0/pci@1/pci@0/isa@2 isa
IOBD/PCIX PCIX IOBD /pci@7c0/pci@0/pci@1/pci@0/usb@5 usb-pciclass,0c0310
IOBD/PCIX PCIX IOBD /pci@7c0/pci@0/pci@1/pci@0/usb@6 usb-pciclass,0c0310
IOBD/PCIX PCIX IOBD /pci@7c0/pci@0/pci@1/pci@0/ide@8 ide-pci10b9,5229
========================= HW Revisions =======================================
System PROM revisions:
----------------------
OBP 4.29.0.a 2008/09/15 12:01
IO ASIC revisions:
------------------
Location Path Device Revision
-------------------- --------------------------------------------- ------------------------------ ---------
MB/SAS-SATA-HBA /pci@780 SUNW,sun4v-pci 0
MB/SAS-SATA-HBA /pci@780/pci@0 pciex10b5,8532.bc 188
MB/SAS-SATA-HBA /pci@780/pci@0/pci@9 pciex10b5,8532.bc 188
MB/IO-BRIDGE /pci@7c0 SUNW,sun4v-pci 0
MB/PCI-BRIDGE /pci@7c0/pci@0 pciex10b5,8532.bc 188
MB/PCI-BRIDGE /pci@7c0/pci@0/pci@8 pciex10b5,8532.bc 188
MB/SAS-SATA-HBA /pci@780/pci@0/pci@9/scsi@0 pciex1000,56.1000.1000.2 2
============================ Environmental Status ============================
Fan sensors:
------------------------------------------------------------
Location Sensor Status
------------------------------------------------------------
NNL084303T:CH/FT0/FM0 RS ok
NNL084303T:CH/FT0/FM1 RS ok
NNL084303T:CH/FT0/FM2 RS ok
NNL084303T:CH/FT2 RS ok
Temperature sensors:
------------------------------------------------------------
Location Sensor Status
------------------------------------------------------------
NNL084303T:CH/IOBD/IOB T_CORE ok
NNL084303T:CH/IOBD T_AMB ok
NNL084303T:CH/MB/CMP0 T_TCORE ok
NNL084303T:CH/MB/CMP0 T_BCORE ok
NNL084303T:CH/MB T_AMB ok
NNL084303T:CH/PDB T_AMB ok
Current sensors:
------------------------------------------------------------
Location Sensor Status
------------------------------------------------------------
NNL084303T:CH/MB I_VCORE ok
NNL084303T:CH/MB I_VMEML ok
NNL084303T:CH/MB I_VMEMR ok
Current indicators:
------------------------------------------------------------
Location Indicator Condition
------------------------------------------------------------
NNL084303T:CH/IOBD I_USB0 ok
NNL084303T:CH/IOBD I_USB1 ok
NNL084303T:CH/FIOBD I_USB ok
Voltage sensors:
------------------------------------------------------------
Location Sensor Status
------------------------------------------------------------
NNL084303T:CH/SC/BAT V_BAT ok
NNL084303T:CH/IOBD V_+1V5 ok
NNL084303T:CH/IOBD V_+1V8 ok
NNL084303T:CH/IOBD V_+3V3MAIN ok
NNL084303T:CH/IOBD V_+3V3STBY ok
NNL084303T:CH/IOBD V_+1V ok
NNL084303T:CH/IOBD V_+1V2 ok
NNL084303T:CH/IOBD V_+5V ok
NNL084303T:CH/IOBD V_-12V ok
NNL084303T:CH/IOBD V_+12V ok
NNL084303T:CH/MB V_+1V5 ok
NNL084303T:CH/MB V_VMEML ok
NNL084303T:CH/MB V_VMEMR ok
NNL084303T:CH/MB V_VTTL ok
NNL084303T:CH/MB V_VTTR ok
NNL084303T:CH/MB V_+3V3STBY ok
NNL084303T:CH/MB V_VCORE ok
LEDs:
------------------------------------------------------------
Location LED State
------------------------------------------------------------
NNL084303T:CH/FT0/FM0 SERVICE off
NNL084303T:CH/FT0/FM1 SERVICE off
NNL084303T:CH/FT0/FM2 SERVICE off
NNL084303T:CH/FT2 SERVICE off
NNL084303T:CH/SYS ACT steady
NNL084303T:CH/SYS LOCATE off
NNL084303T:CH/SYS SERVICE off
NNL084303T:CH/SYS REAR_FAULT off
NNL084303T:CH/SYS TEMP_FAULT off
NNL084303T:CH/SYS TOP_FAN_FAULT off
NNL084303T:CH/HDD0 SERVICE off
NNL084303T:CH/HDD0 OK2RM off
NNL084303T:CH/HDD1 SERVICE off
NNL084303T:CH/HDD1 OK2RM off
NNL084303T:CH/HDD2 SERVICE off
NNL084303T:CH/HDD2 OK2RM off
NNL084303T:CH/HDD3 SERVICE off
NNL084303T:CH/HDD3 OK2RM off
============================ FRU Status ============================
Location Name Status
------------------------------------------------------
NNL084303T:CH/FT0/FM0 FAN enabled
NNL084303T:CH/FT0/FM1 FAN enabled
NNL084303T:CH/FT0/FM2 FAN enabled
NNL084303T:CH/FT2 FAN enabled
NNL084303T:CH SC enabled
NNL084303T:CH IOBD enabled
NNL084303T:CH MB enabled
NNL084303T:CH/MB/CMP0/CH0/R0/D0 DIMM enabled
NNL084303T:CH/MB/CMP0/CH0/R0/D1 DIMM enabled
NNL084303T:CH/MB/CMP0/CH1/R0/D0 DIMM enabled
NNL084303T:CH/MB/CMP0/CH1/R0/D1 DIMM enabled
NNL084303T:CH/MB/CMP0/CH2/R0/D0 DIMM enabled
NNL084303T:CH/MB/CMP0/CH2/R0/D1 DIMM enabled
NNL084303T:CH/MB/CMP0/CH3/R0/D0 DIMM enabled
NNL084303T:CH/MB/CMP0/CH3/R0/D1 DIMM enabled
NNL084303T:CH PDB enabled
NNL084303T:CH FIOBD enabled
NNL084303T:CH SASBP enabled
NNL084303T:CH/PS0 PS enabled
NNL084303T:CH/PS1 PS enabled
============================ FW Version ============================
Version
------------------------------------------------------------
System Firmware 6.6.7 2008/09/29 09:36
====================== System PROM revisions =======================
Version
------------------------------------------------------------
OBP 4.29.0.a 2008/09/15 12:01
Chassis Serial Number
---------------------
NNL084303T
Hello all ,
This is the output of my prtdiag command ...The speed of each of the CPUs is listed below (1281 MHz ) ..That's fine ..I'm confused about the (System clock frequency: 183 MHZ ) ..What is the difference between System Clock freq and CPU freq ...THanks..
System Configuration: Sun... (5 Replies)
Hi everyone,
I am having a problem when running devfsadm. We have many T2000, but on one of them, that is connected to our SAN, devfsadm reports no new disks. If a reconfiguration reboot is done, the system reports the new disk. But only with a reboot. We have Solaris10 installed and Veritas... (13 Replies)
Hi,
I have a netra t2000 running solaris 10. It is fully patched with the latest patch cluster and also patch 118833-36 and 126897-02. The SC sys_event level is set to 3.
I am running a test to show hardware log status, e.g simulating a power supply failure.Hence I unplug one of te... (3 Replies)
Hi All
I have a problem on T2000 server.
bash-3.00# uname -a
SunOS 5.10 aaa Generic_120011-14 sun4v sparc SUNW,Netra-T2000After the initial solaris installation server failed to boot:
Rebooting with command: boot
Boot device: disk:b File and args:
The file just loaded does not appear... (1 Reply)
Hi all,
First post so be gentile :)
It's my first time installing Solaris on T2000 server.
I have 2 72GB HD's on it.
After configuring HW raid and running raidctl command I get this output:
bash-3.00# raidctl -l c0t0d0
Volume Size Stripe Status Cache RAID
... (2 Replies)
hi all
when i trying to give auto-boot value as false as following
#eeprom auto-boot?=false
it is showing as
zsh: no matches found: auto-boot?=false
so felt this is because of error in hard ware so i tried this
#iostat -en
it is showing like
iostat -en
---- errors ---
s/w h/w trn... (4 Replies)
Hi Friends,
I need a help from you all.
In my machine which is on Solaris 9.
the command prtdiag -v shows the complete output but it doesn't show "Memory Module Groups status" status.
I have tried restarting the picl daemon, but still it doesn't work.
Memory Module Groups:... (2 Replies)
Hi everyone,
Please can you tell me what kind of memro we are talking about when we run :
prtdiag -v
Memory size: 98016 Megabytes
Thank you (7 Replies)
selected lines from the output of the "prtdiag -v" command on a T5240 SUN server running Solaris 10.
Are the following known as FRU names and what do they mean?
MB/CMP0/BR0/CH0/D0
MB/CMP0/BR0/CH1/D0
SYS/FANBD0/FM0/F0
SYS/FANBD0/FM0/F1
SYS/MB/CMP0/BR1/CH0/D1 ... (1 Reply)
05-04-2009