Sponsored Content
Operating Systems Solaris USB to Serial Adapter connection Post 302306257 by incredible on Sunday 12th of April 2009 03:35:55 AM
Old 04-12-2009
If you're sure that you're connecting correctly but find that the system "looks hung", you might want to issue a send-break signal to drop the system to OK> prompt. First of all, are you able to remote access your system (ssh, telnet). if your network service is not up, I think its no harm to halt your system and try..
 

10 More Discussions You Might Find Interesting

1. Linux

modem - usb to serial configuration

I have a serial modem connected to a usb port using an adapter cable. The system is a HP DL360. RedHat ES3.0 I am using the device /dev/ttyUSB0 When I issue the command "mgetty ttyUSB0" I get the following output in the log file. How do I get the system to see the modem. 12/02 14:17:55... (2 Replies)
Discussion started by: jshoovie
2 Replies

2. UNIX for Dummies Questions & Answers

isa serial port adapter card no longer detectedworking

hi all, i've got an old PC with unix (SCO System V/386 rel. 3.2) on it. Pentium I; 128mb; ISA 2-port RS232 serial adapter card for an oki dot-matrix printer. (no usb, no CD) i've been running an old cobol program to do some invoicing and print reports. some time back i changed the... (0 Replies)
Discussion started by: frankpky
0 Replies

3. SCO

Usb To Serial (sco6)

According to sco6 usb supplement, once you install it, you can install a bafo industries (BF-810) in the computer. I have done all that and followed the intructions completely and it shows up using usbprobe and l /dev/usb_ser* Problem is that when I go to mkdev serial, it is not there. Anyone... (1 Reply)
Discussion started by: jn5519
1 Replies

4. Solaris

Usb to serial connection to Sun Enterprice 450

Hi all, I must connect my PC (Windows 2000) to Sun Enterprise 450 (4 X UltraSPARC-II 400Mhz) for Solaris 10 Installation. My PC doesn't have a serial port therefore I must use USB port. How can I connect USB port of my PC to the serial port (DB 25) of Sun 450? Will be there any problems with... (3 Replies)
Discussion started by: Sunb3
3 Replies

5. UNIX for Dummies Questions & Answers

USB serial help needed

Hi iam new bie to unix. we are getting the sensor positional values on hyperterminal(UART).but our task is to use this data for mouse movement.so wat we hav to do ?? is this required to change usb driver cud u send info regarding my query?? Thanks in advance :) :) :) (1 Reply)
Discussion started by: jayakar
1 Replies

6. IP Networking

my wireless usb adapter connect to net but the signal is very weak

i have wireless usb adapter rtl8187 from micromax company my proplem is the signal is very weak and i cannot open website can i increase the signal ? iwconfig lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0... (5 Replies)
Discussion started by: rsd220
5 Replies

7. Solaris

Detecting wirelss USB Adapter

Hi, i try to plug in my USB wireless adapter to my sun solaris server. However, it cannot detect it. How do i set it so that it can detect it? (1 Reply)
Discussion started by: lkyow
1 Replies

8. Hardware

How to install a driver of my USB-A to Serial Cable

Hi Gurus of Unix Recently I install a OpenSolaris in My HP 530 In this moment want to install a USB-A to Serial Cable. Any guru can send a Link where I can use how reference. I want to configure a Router and my PC don't have any serial Port. My LapTOP only has USB ports. In this case I buy a... (2 Replies)
Discussion started by: andresguillen
2 Replies

9. Solaris

Solaris 11.2 does not assign serial port to 3g usb modem?

In ubuntu etopic i create this udev rules for prolink 3g usb modem: SUBSYSTEM=="block", SUBSYSTEM=="scsi", ATTRS{idVendor}=="1e0e", ATTRS{idProduct}=="f000", ACTION=="add", RUN+="/sbin/modprobe usbserial Vendor=0X1e0e Product=0Xf000" After plugging the usb modem, ubuntu assigns the ports... (4 Replies)
Discussion started by: shamsat
4 Replies

10. Linux

Connect from USB to serial port of switch

I have someone wanting to connect to the serial management port of a switch from a PC running CentOS6. The management port on the switch is apparently baud 9600, 8 data bits, 1 stop bit & no parity They have plugged in a cable to connect and the output from lsusb is:-Bus 001 Device 001: ID... (7 Replies)
Discussion started by: rbatte1
7 Replies
SYSTEMD-HALT.SERVICE(8) 				       systemd-halt.service					   SYSTEMD-HALT.SERVICE(8)

NAME
systemd-halt.service, systemd-poweroff.service, systemd-reboot.service, systemd-kexec.service, systemd-shutdown - System shutdown logic SYNOPSIS
systemd-halt.service systemd-poweroff.service systemd-reboot.service systemd-kexec.service /lib/systemd/systemd-shutdown /lib/systemd/system-shutdown/ DESCRIPTION
systemd-halt.service is a system service that is pulled in by halt.target and is responsible for the actual system halt. Similarly, systemd-poweroff.service is pulled in by poweroff.target, systemd-reboot.service by reboot.target and systemd-kexec.service by kexec.target to execute the respective actions. When these services are run, they ensure that PID 1 is replaced by the /lib/systemd/systemd-shutdown tool which is then responsible for the actual shutdown. Before shutting down, this binary will try to unmount all remaining file systems, disable all remaining swap devices, detach all remaining storage devices and kill all remaining processes. It is necessary to have this code in a separate binary because otherwise rebooting after an upgrade might be broken -- the running PID 1 could still depend on libraries which are not available any more, thus keeping the file system busy, which then cannot be re-mounted read-only. Immediately before executing the actual system halt/poweroff/reboot/kexec systemd-shutdown will run all executables in /lib/systemd/system-shutdown/ and pass one arguments to them: either "halt", "poweroff", "reboot" or "kexec", depending on the chosen action. All executables in this directory are executed in parallel, and execution of the action is not continued before all executables finished. Note that systemd-halt.service (and the related units) should never be executed directly. Instead, trigger system shutdown with a command such as "systemctl halt" or suchlike. SEE ALSO
systemd(1), systemctl(1), systemd.special(7), reboot(2), systemd-suspend.service(8) systemd 237 SYSTEMD-HALT.SERVICE(8)
All times are GMT -4. The time now is 02:51 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy